manualshive.com logo in svg

Gardenline GLPC 41, Общее руководство пользователя, Страница: 51 / 72

Поделиться
Скачать
Gardenline GLPC 41 Скачать руководство пользователя страница 51

AFTER SALES SUPPORT

   

  0151 649 1500      

  1890 946244

  www.einhell.co.uk

55

 

 

41cc Petrol Chainsaw – GLPC 41

Cleaning

Cleaning

 

CAUTION!

Set the On/Off switch to Stop (0) & disconnect the spark 

plug boot (Fig. 24b/pos. D - See page 58) before doing 

any cleaning and maintenance work! Risk of electric shock, 

if the engine is running.

Carrying out any cleaning work

–   The equipment should be cleaned thoroughly every time after it has been used. 

This applies particularly to the chain and bar.

–    Keep the air vents and the motor housing free of dirt and dust as far as possible. 

Wipe the equipment with a clean damp cloth or blow it down with compressed air 

at low pressure.

–  It is easiest to remove sawdust and wood chippings immediately after use.

–   Clean the equipment regularly with a damp cloth and some soft soap. Do not use 

cleaning agents or solvents; these may be aggressive to the plastic parts in the 

equipment. Ensure that no water can get into the interior of the equipment.

Содержание GLPC 41









































































Отзывы:

Нет отзывов