manualshive.com logo in svg

Gardenline GLPC 41, Общее руководство пользователя, Страница: 62 / 72

Поделиться
Скачать
Gardenline GLPC 41 Скачать руководство пользователя страница 62

AFTER SALES SUPPORT

   

  0151 649 1500      

  1890 946244

 

 

  www.einhell.co.uk

66

41cc Petrol Chainsaw – GLPC 41

Maintenance and servicing

Chain maintenance (continued) 

Chain tension 

Check the chain tension frequently and adjust as often as necessary to keep the chain 

snug on the bar, but loose enough to be pulled around by hand (See page 35). 

Breaking in a new saw chain 

A new chain and bar will need chain readjustment after as few as 5 cuts. This is normal 

during the break-in period, and the interval between future adjustments will begin to 

lengthen quickly. 

 

CAUTION!

Never have more than 3 links removed from a loop of chain. 

This could cause damage to the sprocket. 

Chain lubrication 

Always make sure the automatic oiler system is working properly. Keep the oil tank filled 

with Chain, Bar and Sprocket Oil.
Adequate lubrication of the bar and chain during cutting operations is essential to 

minimize friction with the guide bar. 
Never starve the bar and chain of lubricating oil. Running the saw dry or with too little oil 

will decrease cutting efficiency, shorten saw chain life, cause rapid dulling of chain, and 

lead to excessive wear of bar from overheating. Too little oil is evidenced by smoke or bar 

discolouration.

NOTICE!

 Store the equipment in a dry place and far away from possible 

ignition sources such as an oven, a gas-fired hot water boiler, 

a gas-fired dryer, etc.

Содержание GLPC 41









































































Отзывы:

Нет отзывов