Gardenline GLPC 41 Скачать руководство пользователя

Страница: 33 / 72

AFTER SALES SUPPORT

0151 649 1500

1890 946244

www.einhell.co.uk

41cc Petrol Chainsaw – GLPC 41

Set up

3. Chain brake mechanical test

Your chainsaw is equipped with a chain brake that reduces the possibility of injury due to

kickback. The brake is activated if pressure is applied against the brake lever when, as in

the event of kickback, the operator's hand strikes the lever. When the brake is actuated,

chain movement stops abruptly.

WARNING!

The purpose of the chain brake is to reduce the possibility

of injury due to kickback; however, it cannot provide the

intended measure of protection if the saw is operated

carelessly. Always test the chain brake before using your saw

and periodically while on the job. (See below for details of

how to perform a test of the mechanical brake).

Fig. 10a

Fig. 10b

To test chain brake

– The chain brake is

DISENGAGED (chain can move) when the BRAKE LEVER IS PULLED

BACK AND LOCKED (Fig. 10a).

– The chain brake is

ENGAGED (the chain is locked) when the brake lever is pulled

forward and the mechanism (Fig. 10b/pos. A) can be seen. It should not be possible

to move the chain (Fig. 10a/pos. A).

Содержание GLPC 41









































































Результаты поиска

Содержание GLPC 41

Отзывы:

Похожие инструкции для GLPC 41

Бренды по названию

Популярные бренды

Gardenline GLPC 41, Общее руководство пользователя

Результаты поиска

Содержание GLPC 41

Отзывы:

Похожие инструкции для GLPC 41

Бренды по названию

Популярные бренды