FUTABA 8UHFS Скачать руководство пользователя | Manualshive

Страница: 38 / 101

background image

35

This function is used to select the type of model to be programmed in the current

model memory. You may select from helicopters of five swash types
(HELISWH1/SWH2/SWH4/SR-3/SN-3), aircraft (ACRO), and gliders with one or
two flap servos (GLID1FLP, GLID2FLP).

Swashplate Type Setting Procedure

HELISWH1 Type
This type’s helicopter has independent aileron and elevator servos linked to the
swashplate. Most kits are HELISWH1 type.

HELI SWH2 Type
Use SWH2 mixing when the pushrods are
positioned as shown in the figure. Elevator
operates with a mechanical linkage.

Pitch

Aileron

Front

With Aileron inputs, the aileron and pitch
servos tilt the swashplate left and right;
With Pitch inputs, the aileron and pitch servos
raise the swashplate up and down.

HELI SWH4 Type
If the servo inputs are located as shown, use
SWH4 Mixing.

Aileron

Pitch

Front

(Pitch)

(Aileron)

Elevator 1

Elevator 2
(CH8)

With Aileron inputs, the aileron and pitch
servos tilt the swashplate left and right;
With Elevator inputs, the servos tilt the
swashplate fore and aft;
With Pitch inputs, all four servos raise the
swashplate up and down.

HELI SR-3 Type
If the servo inputs match the figure, use SR-3
Mixing.

Aileron

(Pitch)

Pitch

(Aileron)

Front

Elevator

120

120

120

With Aileron inputs, the aileron and pitch
servos tilt the swashplate left and right;
With Elevator inputs, the three servos tilt the
swashplate fore and aft;
With Pitch inputs, all three servos raise the
swashplate up and down.

«
...
36
37
38
39
40
...
»

Содержание 8UHFS






































































































Отзывы:

Нет отзывов

Похожие инструкции для 8UHFS

DELTAFLUX MT100

Бренд: PIETRO FIORENTINI Страницы: 16

Бренд: ZETRON Страницы: 3

Бренд: Quectel Страницы: 23

Бренд: Quectel Страницы: 79

Бренд: Barco Страницы: 6

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 35

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 73

Бренд: Eaton Страницы: 4

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 14

Бренд: Eaton Страницы: 36

Бренд: K&K Страницы: 6

Бренд: Zodiac Страницы: 12

Бренд: National Instruments Страницы: 34

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Бренд: Scanreco Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды