FUTABA 8UHFS Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 101

background image

71

5. Link function setting

Turn the Link function ON or OFF
with the (+)/(-) keys. When the Link
function is ON, ">" is displayed
after the slave channel on the
screen.

6.

Trim setting

This couples the master
channel's trim with the slave
function. Select ON/OFF with
the (+)/(-) keys.

Trim ON/OFF indicator

Link function ON/OFF
indicator

• If you select "STK-3" to turn mixer
on and off, you’ll need to set the
switching position and direction. To
do so, first position the throttle stick
where you want switching to occur.
Next, enter the stick position into
memory by pressing the (+)/(-) keys
simultaneously. (a percentage will be
displayed on the screen.
If you want mixing turned on at the
high throttle side of the set position,
press the (+) key. If you want mixing
on at the low throttle side, press the
(-) key. An arrow is displayed above
or below the small "3" at the right top
corner of the screen to verify proper
switching direction.
When you think you're done, move
the throttle stick and check if
programmable mixing switches on
and off in accordance with your
settings.

(Continued from preceding page)

7. Offsetting neutral mix point
If you want the mix to occur
somewhere besides master
neutral, hold the master
channel control in the desired
position, and store the offset
position by pressing the (+)/(-)
keys simultaneously.

Displays offset position

8. Switch selection

Choose the desired mixer
ON/OFF switch with the (+)/(-)
keys.

Displays
ON/OFF switch
direction

Current
on/off
switch

NULL = Normal operation regardless of switch setting
UP = Switch upper or rear position turns on the function
CNTR = Center position of 3-position switch turns on the function
DOWN = Switch lower or forward position turns on the function

9. ON/OFF Direction

Set the ON/OFF directions with
the (+)/(-) keys.

4. Input 5-point curve values

Select the curve position “POS1” with the
CURSOR keys and set the rate with
the (+)/(-) keys.

-If you’re unhappy with what you’ve

Set rate

(Mixer# 6-7 only)

Range:-100 to +100%

(Initial value: 0%)

set, you may return to the default

value by presing the (+) and (-) keys

simultaneously.

Master channel control

5-point curve

+100%

0%

POS1 POS2 POS3 POS4 POS5

-100%

Mixing

rate

Initial value (0%)

UP/C = Uper and center position of 3-position switch turn on
the function.

C/DN = Center and lower position of 3-position switch turn on
the function.

(Mixer# 1-5 only)

(Mixer# 1-5 only)

«
...
72
73
74
75
76
...
»

Содержание 8UHFS






































































































Отзывы:

Нет отзывов

Похожие инструкции для 8UHFS

Бренд: Eaton Страницы: 86

Бренд: Jetline Страницы: 58

Бренд: Ebyte Страницы: 35

Бренд: UCS Страницы: 4

Бренд: Maestra Страницы: 22

Бренд: Veeder-Root Страницы: 27

Бренд: Valve Concepts Страницы: 18

Бренд: K&K Страницы: 6

Бренд: Auber Страницы: 3

Бренд: Quickie Страницы: 108

Бренд: GARDINER TECHNOLOGY Страницы: 28

SmartScene IR Remote Series

Бренд: Thorlux Lighting Страницы: 2

VEGACAP 60 Series

Бренд: Vega Страницы: 12

Бренд: D+H Страницы: 17

Бренд: Partlow Страницы: 49

Бренд: Ascon tecnologic Страницы: 11

Бренд: ROBOT3T Страницы: 21

Бренд: StudioComm Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды