FUTABA 8UHFS Скачать руководство пользователя | Manualshive

Страница: 57 / 101

background image

54

The gyro mixing function is used to adjust the gyro sensitivity from the transmitter.

Use this function by connecting the gyro sensitivity adjustment input connector to the
channel 5 output of the receiver. Switch H or switch G (idle-up switch) can be
selected, and each direction of the changeover switch can be adjusted.

Switch H: The UP and DOWN sides sensitivity can be adjusted.
Switch G: The NORM, IDL1, and IDL2 sensitivities can be adjusted.

Entering Gyro Sensitivity Values

To GOVrpm
function

To HOV-PI
function

Switch

direction

display

Data input keys

These keys are used to move
around in the GYRO menu.

2. “UP” side setting

Enter your desired sensitivity value
with the (+)/(-) keys.
3. “DOWN” side setting
Enter your desired sensitivity value
with the (+)/(-) keys.
4. Switch selection
Slect the desired switch with the
(+)/(-) keys.

Switch H: UP, DOWN
Switch G: NORM, IDL1,IDL2

Sensitivity amount

Range: 0 to 100%
(Initial value: 50%)

1. Activate Gyro Mixing Function
Press the (+) key to activate the GYRO function.

( Use the (-) key to INHibit the mixer.)

The Governor mixing function is used to adjust the GV-1 (Governor) speed

settings (rS1, rS2, rS3) from the transmitter. Whether speed switching and governor
ON/OFF are switched using one switch or ON/OFF switching is performed using an
independent switch can also be selected. When speed setting control uses CH7 and an
ON/OFF switch is used, CH8 can also be used.

When speed and ON/OF are switched using one switch
(Setting example)

Governor Speed

Switch Position

(Switch C or G)

Rate

(%)

Adjustment from Transmitter

rS1: OFF

rS2: 1400
rS3: 1700

UP or NORM

CNTR or IDL1

DOWN or IDL2

0

50

100

Use up to 0% (Governor speed display: "off")
Speed adjusted by raising and lowering "50%" rate.
Speed adjusted by lowering "100%" rate.

* For instance, rS3 is adjusted by setting the maximum speed used and lowering it
from the transmitter.
* For the time being, use the initial rate setting above.
* Since speed adjustment from the transmitter is rate setting, for the actual speed,
checking the governor side display and remembering its relationship with the actual
speed is convenient.

When governor ON/OFF is controlled using switch B
When governor ON/OFF uses an independent switch, the speed can be adjusted and
switched using each position (3 points) of switch C or G.

«
...
55
56
57
58
59
...
»

Содержание 8UHFS






































































































Отзывы:

Нет отзывов

Похожие инструкции для 8UHFS

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

Бренд: NEJE Страницы: 17

Бренд: Oceanic Страницы: 13

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 26

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды