FUTABA 8UHFS Скачать руководство пользователя | Manualshive

Страница: 93 / 101

background image

-90-

90

The Speed function is used to offset

the aileron, elevator, and flap servos to the
position that provides maximum drag for
cruise and high-speed flight.    Normally
the ailerons and flaps are raised about 3-
5°.    Some airfoils, notably the RG-15,
actually have higher drag with reflex, so
Speed function should not be used with
this section and other similar ones.    The
elevator neutral can also be offset in order
to trim out any pitch changes caused by
the trailing edge reflex.    This function is
activated by flipping switch G to the
forward position.

If you wish to have the three-position

switch above the left-hand stick (position
E), you should purchase the 8UH system.

Speed presets

Inputting the Speed presets for your model

To PMIX-1 function

To START function

Channel
being offset
for START

2. Aileron 1 offset
Input the desired Aileron 1
offset with the (+)/(-) keys.
3. Elevator offset
Input the desired Elevator
offset with the (+)/(-) keys.
4. Flap offset*
Input the desired Flap offset
with the (+)/(-) keys.
5. Aileron 2 offset
Input the desired Aileron 2
offset with the (+)/(-) keys.

(You may reset to zero by
pressing the (+)/(-) keys
simultaneously.)

Data input keys

These keys are used to move through the

five submenus in the SPEED function.

Turn the SPEED function ON by pressing the (+)
key ("ON" or "OFF" displayed depending on
Switch G position). Turn off (INH) the function
with the (-) key.

Servo offset
Range: -100 to +100%
Initially set to 0%

*The GLID 2FLP menu for SPEED has
separate Flap 1 and Flap 2 offsets.

«
...
91
92
93
94
95
...
»

Содержание 8UHFS






































































































Отзывы:

Нет отзывов

Похожие инструкции для 8UHFS

Relion 670 series

Бренд: ABB Страницы: 760

Бренд: ABB Страницы: 128

Бренд: jbc Страницы: 4

Бренд: C.Nord Страницы: 100

CoreBuilder 9000

Бренд: 3Com Страницы: 78

Бренд: Zeagle Страницы: 37

Бренд: Vacon Страницы: 50

Бренд: V2 Страницы: 116

Бренд: V2 Страницы: 8

Бренд: V2 Страницы: 25

Бренд: V2 Страницы: 124

Бренд: D+H Страницы: 32

Бренд: UniPOS Страницы: 6

Бренд: Vag Страницы: 19

Бренд: Carrier Страницы: 86

Бренд: Hoffer Страницы: 57

Бренд: KanexPro Страницы: 28

Бренд: Flowserve Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды