FUTABA 8UHFS Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 101

background image

73

The Flap Trim function is used to specify the amount of flap travel (or camber, if on a
sailplane setup).    If flaperon (FLPRON) mixing is active, FLAPTRM is automatically turned
on.    You should match the travel of both flaps before using this function to set the total
amount of flap throw.    The amount depends on the model, but for sailplanes a small amount
(less than 10%) is preferred, since too much camber produces excessive drag.    Don’t use
more than about 1/16” travel up or down (some airfoils, such as the RG-15, should be flown
with NO reflex).

Setting Flap Trim function

To AI-DIF function

To FLPRON function

Trim range of values
Range: -100 to +100%
Initially set to 0%

Flap travel adjustment
Adjust the flap travel with the
(+)/(-) keys.
Press the (+)/(-) keys
simultaneously to return to
0%.

Data input keys

These keys are used to move through the

two submenus in the FLPTRM function.

Turn the FLPTRM function ON or OFF by
pressing the (+) key ("ON" displayed ). Turn off
(INH) the function with the (-) key.

The differential function allows you to program the
amount of ‘up’ aileron travel independently from the
amount of down travel when you have two servos
plugged into the receiver (right aileron = CH1/AIL
and left aileron = CH7).
NOTE: Only one of the three functions aileron
differential, flaperon, or elevon can be used at a time.
The last function activated overrides the others. If
you need both flaperons and differential, activate the
FLPRON function and in its menu set different up
and down aileron travels to provide differential.

CH7

CH1

Setting up aileron differential in AI-DIF

To ABRAKE function

To FLPTRM function

Travel Range: -120 to +120%
Initially settings are 100%

Right aileron servo (CH1) travel
Move the aileron stick in both
directions and set the travel in each
direction with the (+)/(-) keys.

Left aileron servo (CH7) travel
Press the right (>) key and repeat
travel adjustment as done for CH1.

• Press the (+)/(-) keys
simultaneously to return to 0%.

Data input keys

These keys are used to move through the

three submenus in the AI-DIF function.

Turn the AI-DIF function ON by pressing the (+) key ("ON"
displayed ). Turn off (INH) the function with the (-) key.

Amount of servo
travel for left
stick motion

Amount of servo
travel for right
stick motion

«
...
74
75
76
77
78
...
»

Содержание 8UHFS






































































































Отзывы:

Нет отзывов

Похожие инструкции для 8UHFS

Бренд: Gardena Страницы: 18

VLT Micro Drive FC 51 Series

Бренд: Danfoss Страницы: 23

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Бренд: K'Nex Education Страницы: 56

Бренд: B&G Страницы: 19

Cutler-Hammer Jockey

Бренд: Eaton Страницы: 12

Бренд: National Instruments Страницы: 14

Бренд: Sartorius Страницы: 165

PersonalWorkplace Pro Video

Бренд: G&D Страницы: 56

Бренд: Beninca Страницы: 16

Бренд: Woodward Страницы: 118

Бренд: Nordson Страницы: 20

Бренд: D+H Страницы: 16

Бренд: CompuPro Страницы: 33

Бренд: AUMA Страницы: 168

Бренд: END ARMATUREN Страницы: 32

Бренд: Nice Страницы: 40

Network Device NXC-8160s

Бренд: ZyXEL Communications Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды