FUTABA 8UHFS Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 101

background image

39

The 8UH has digital trims which are different from conventional mechanical trim
sliders. Each trim control is actually a two-direction switch.    Each time the trim
switch is pressed, the trim is changed a selected amount.    When you hold the trim
lever, the trim speed increases.    The current trim position is graphically displayed on
the screen.    The Trim function includes a number of submenus that are used to
manage the trim options.    This may be better understood by viewing the menu
structure on p. 20.

To SUBTRM function

To INVERT function

"NEXT" indicates that there is
a group of submenus in the
TRIM function .

Select the desired function in
the TRIM submenu with the
(>) and (<) CURSOR keys.

Data input keys

These keys are used to move through submenus in the TRIM function.

TRIM functions:
• Trim Reset
• Trim Step Rate
• Trim Reverse Display

The Trim Reset function electronically centers the trims to their default values. Note
that the subtrim settings and the trim step rate are not reset by this command.

Resetting trims

To SUBTRM function

To INVERT function

If any trim is not centered, the
"RSET" flashes.

To Reset Trim, press the (+)
and (-) keys simultaneously.
When you do, "RSET" stops
flashing.

Data input keys

These keys are used to move through submenus in the TRIM function.

The Trim Step menu may be used to change the rate at which the trim moves when the
trim lever is activated. It may be set to a value ranging from 1 to 40 units, depending
on the characteristics of the aircraft. Most ordinary aircraft do well with their trim
step rate set to about 2 to 10 units.

To SUBTRM function

To INVERT function

Step rate
Range: 1 - 40
Factory setting: 4

SETTING TRIM STEP RATE
Use the (+) and (-) keys to set
the aileron trim step rate.
When done, select elevator
trim with the (>) key. Again
use the (+) and (-) keys to set
the elevator trim step rate

Data input keys

These keys are used to move through submenus in the TRIM function.

Channel being set

You can set the throttle and rudder trims in a similar
fashion. If you’re unhappy with your settings, you
may return to the default value by pressing the (+)
and (-) keys simultaneously.

«
...
40
41
42
43
44
...
»

Содержание 8UHFS






































































































Отзывы:

Нет отзывов

Похожие инструкции для 8UHFS

Бренд: ABB Страницы: 30

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 44

Бренд: Fairchild Страницы: 2

Бренд: Fagor Страницы: 103

Бренд: UNITED Страницы: 8

Бренд: Kamstrup Страницы: 36

Бренд: JFA Electronicos Страницы: 29

Бренд: X Rocker Страницы: 38

Бренд: York Страницы: 24

Бренд: Zeta Страницы: 44

Бренд: LLURIA Страницы: 2

PDS CONTROL Series

Бренд: S&P Страницы: 32

Бренд: Objective Imaging Страницы: 11

Бренд: ICP DAS USA Страницы: 6

Бренд: Bentel Страницы: 88

Бренд: Zenith Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды