FUTABA 8UHFS Скачать руководство пользователя | Manualshive

Страница: 75 / 101

background image

72

The Flaperon mixing function uses two servos to

individually control two ailerons, combining the
aileron function with the flap function.    For a flap
effect, the ailerons can be raised and lowered
simultaneously.    Of course, aileron function, where
the two controls move in different directions, is also
performed.    The up and down travel of the left and
right ailerons can be adjusted independently, so you
can also get a differential effect.   Left and right
flap travel can be adjusted individually.  You can
combine the Flaperon function with the airbrake
function, to get steep descents without building up
airspeed, which is very convenient for small or
narrow fields.  To take advantage of the flaperon
mixing function, you’ll need to connect the right
aileron servo to CH1 (AIL) and the left aileron servo
to CH6 (FLP).

CH6

CH1

NOTE: Only one of the three functions flaperon, aileron differential, or elevon can be used at
a time. All three functions cannot be activated simultaneously. The last function activated
overrides the others.

Setting up the Flaperon function

Turn the FLPRON function ON by pressing the (+) key
("ON" displayed). Turn off (INH) the function with the (-)
key.

To

FLPTRM

function

To MIX-7 function

Amount of
aileron travel for
left aileron stick

Data input keys

These keys are used to move
around in the FLPRON menu

2. Right aileron adjustment
Move the aileron stick in the direction
you want to adjust and set the value
with the (+)/(-) keys.

3. Left aileron adjustment
Again move the aileron stick in the
direction you want to adjust and
set the value as before.
• If you're unhappy with what you've
set, you may return to the default
value by pressing the (+) and (-)
keys simultaneously.

4. Flap 2 adjustment
Adjust flap 2 with the
(+)/(-) keys.
5. Flap 1 adjustment
Adjust flap 1 with the
(+)/(-) keys.

Flap being
adjusted
(FLP2 or
FLP1)

Servo travel rate
(Range: -120 to +120%)
(Initial s100%)

Amount of
aileron travel
for right stick

Range: -120 to +120%)
(Initial s100%)

You must have a Flap trim that is not zero to adjust flap travels.

When you move
the control below

CH1 servo
functions as

CH6 servo
functions as

Aileron stick

Right aileron

Left aileron

Flap control knob Flap 2

Flap 1

Note: use the FLP1 and FLP2 settings to match flap travels
on both sides. Then use FLPTRM to set the total throw you
want.

«
...
73
74
75
76
77
...
»

Содержание 8UHFS






































































































Отзывы:

Нет отзывов

Похожие инструкции для 8UHFS

Бренд: Bartlett Страницы: 30

Бренд: Parker Страницы: 21

Бренд: Parker Страницы: 26

Бренд: Parallax Страницы: 3

Бренд: Zaiput Flow Technologies Страницы: 10

Бренд: SMC Networks Страницы: 10

Hydropan-Single

Бренд: ETNA Страницы: 12

Бренд: Water Specialist Страницы: 60

Бренд: aerl Страницы: 27

Бренд: Lumel Страницы: 32

U-verse TV Standard Remote Control

Бренд: AT&T Страницы: 2

Бренд: Nitecore Страницы: 2

Бренд: Joyonway Страницы: 8

Бренд: SIATA Страницы: 7

Бренд: Eaton Страницы: 2

ESCALA Power7 5802

Бренд: Bull Страницы: 48

Бренд: LEGRAND Страницы: 2

Genesis MX-900 Complete Control

Бренд: Universal Remote Control Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды