FUTABA 8UHFS Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 101

background image

25

flight conditions. You can set different delays
for aileron, elevator, and rudder. The delays you
set apply to all flight conditions. We recommend
trying very small values for the initial settings, say
5 - 10%. A 25% delay is about a half-second
transit time between neutral settings.

22. Gyro sensitivity should be controlled
with the CH5 switch. High is normally used
for hovering, and low in other flight
conditions.

You may use the Hovering Pitch and

Hovering Throttle functions for fine trimming
changes due to humidity, etc.

This concludes the example setup procedure

for helicopters.  Be sure to browse through the
pages following this example to see what other
menus are available for helicopters, such as
Hovering Throttle and Pitch knobs, OFST, ACC,
DELAY, and INVERT CROSS.    You may use a
mixer to adjust gyro sensitivity, or to enhance
flight capabilities or to correct a response you
don’t like.    Again, we recommend you set up and
trim in the Normal flight condition before setting
up the alternate flight modes.

This procedure assumes helicopter is trimmed for hovering. Trimming must be done

in near-calm conditions. Repeat tests several times before making adjustments. If any
changes are made, go back over the previous steps and verify, or further adjust as necessary.

To test _

Test Procedure

Observations

Adjustments

1. Revo
mixing — Up
settings (Part 1)

Fly the model straight
and level into the wind
at 100 ft altitude, lower
pitch to 0°

Observe rotation as copter

descends

A. No rotation
B. Model rotates

counterclockwise

C. Model rotates clockwise

A. None
B. Add right rudder

trim

C. Add left rudder

trim

2. Revo
mixing — Up
settings (Part 2)

Bring the copter into
hover, add full pitch and
ascend 75 ft

Observe rotation as copter

ascends

A. No rotation
B. Model rotates

counterclockwise

C. Model rotates clockwise

A. None
B. Increase UP revo

mix

C. Decrease UP revo

mix

3. Revo Down
mixing settings

Begin Down Revo
mixing with same
number as UP mix.
From inverted flight (top
of loop, or mid-point of
roll, or inverted part of
split-S), add full
negative pitch

Observe rotation as copter

ascends

A. No rotation
B. Model rotates clockwise
C. Model rotates

counterclockwise

A. No adjustment
B. Increase Down

revo mix

C. Decrease Down

revo mix

«
...
26
27
28
29
30
...
»

Содержание 8UHFS






































































































Отзывы:

Нет отзывов

Похожие инструкции для 8UHFS

Бренд: DAV TECH Страницы: 10

Бренд: Tapeswitch Страницы: 13

Бренд: Garmin Страницы: 220

Бренд: Gardena Страницы: 16

Gemini GEM-P9600

Бренд: NAPCO Страницы: 6

Gemini GEM-P816

Бренд: NAPCO Страницы: 56

Бренд: Rain Bird Страницы: 20

Бренд: S&P Страницы: 17

Бренд: S&S Northern Страницы: 9

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: Fingertips Lab Страницы: 15

Бренд: TWR Lighting Страницы: 49

Бренд: Water Specialist Страницы: 36

Бренд: UniPOS Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды