manualshive.com logo in svg

Furuno NAVpilot 711C, Руководство оператора, Страница: 95 / 176

Поделиться
Скачать
Furuno NAVpilot 711C Скачать руководство пользователя страница 95

5.  MAINTENANCE, TROUBLESHOOTING

5-7

5.3.9

Rudder test

The rudder test checks drive type, presence or absence of bypass/clutch circuit, etc. 
Open the diagnostic test options window, select [Rudder Test] then push the 

Course 

control

 knob.

Note: 

The rudder test is not available when [Boat Type] is set to [EVCS Boat].

When the rudder reference unit is installed

1. Open the diagnostic test options window, select [Rudder Test] then push the 

Course control

 knob.

The message shown below appears.

2. Center the rudder then push the 

Course control

 knob.

During the test, the message shown below appears.

When the rudder test is completed, the message shown below appears.

Note: 

If the rudder test is not completed satisfactory, the steering mode can not 

be changed from the STBY mode.

3. Press any key to show the test result.

For detail of the test result, see "The result of the rudder test" on page 5-10.

Use wheel to
center rudder before
rudder test.
Are you sure?

Yes

No

Testing Rudder-PLS Wait.
Push any key to abort

Rudder test completed.
Push any key to continue

Содержание NAVpilot 711C

















































































































































































Отзывы:

Нет отзывов