Furuno NAVpilot 711C Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 176

Furuno NAVpilot 711C Скачать руководство пользователя страница 64

2. STEERING MODES

2-40

2.14

Power Assist Mode

The power assist mode, available with the Accu-Steer FPS 12V/24V type drive, cus-
tomizes manual steering to your own preferences. The mode is available during the
safe helm mode and the STBY mode. The indication “

” appears at top of the

screen when this mode is active.

How to set the power assist mode

1. Long press the

key to open the menu in the STBY mode.

2. Rotate the

Course control

knob to select [Other Menu] then push the knob.

3. Rotate the

Course control

knob to select [Safe Helm/P.Assist Setup] then push

the knob.

4. Rotate the

Course control

knob to select the current setting for [Power Assist]

then push the knob.

5. Rotate the

Course control

knob to select [ON] then push the knob.

When this is done the menu items for the power assist mode appear.

6. Rotate the

Course control

knob to select the current setting value for [For

Speeds Under] then push the knob.

7. Rotate the

Course control

knob to set the highest speed at which power assist

activates (setting range: 1.0-9.9 kn).

Note:

When the power assist activates at high speed, the vessel may turn faster

than intended. Set [For Speeds Under] according to the vessel and rudder feature.

N

30

330

300

359

°

HDG

T

This icon appears when the
power assist mode is active.

Safe Helm: ON

Return Delay 5 sec

Safe Helm Response

Safe Helm Beep: ON

Power Assist:

ON

For Speeds Under 10.0kn

Power Assist STBY: OFF

Power Assist Rudder Speed

Safe Helm/P.Assist Setup

«
...
62
63
64
65
66
...
»

Содержание NAVpilot 711C

















































































































































































Отзывы:

Нет отзывов