Furuno NAVpilot 711C Скачать руководство пользователя страница 157 | Manualshive

Страница: 157 / 176

Furuno NAVpilot 711C Скачать руководство пользователя страница 157

7. INITIAL SETTINGS

7-45

7.17

RC (Remote Controller) Setup Menu

The [RC Setup] menu sets the type of remote controller connected to the NAVpilot. To
open the [RC Setup] menu, select [RC Setup] from the [Installation Menu] window.

Note:

The [RC Setup] menu is not shown in case of Fantum Feedback

™

.

1. The cursor is selecting the current setting for [Remote Controller1]; push the

Course control

knob.

2. Rotate the

Course control

knob to select the type of remote controller connected

then push the knob.
[NFU]: Select for lever-type remote controller.
[FU]: Select for dial-type remote controller
[Dodge]: Select for dodge-type remote controller.
[Disable]: Disable remote controller operation.

3. Set the type for [Remote Controller2], if connected.

7.18

All Clear (Default Setting)

The all clear feature restores all default settings.

1. In the STBY mode, push the

Course control

knob three times while pressing the

key.

The [Installation Menu] window appears.

2. Rotate the

Course control

knob to select [System Setup] then push the knob.

3. Rotate the

Course control

knob to select the option for [Restore Factory Setting]

then push the knob.

4. Rotate the

Course control

knob to select [Yes] then push the knob.

RC Setup

Remote Conroller1:

Disable

Remote Conroller2: Disable

«
...
155
156
157
158
159
...
»

Содержание NAVpilot 711C

















































































































































































Отзывы:

Нет отзывов