Furuno NAVpilot 711C Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 176

Furuno NAVpilot 711C Скачать руководство пользователя страница 110

6. INSTALLATION AND WIRING

6-6

6.2.1

Wiring notices

Keep the following wiring notices in mind.

• To connect a single control unit, use pin no. 1 to 7 of the TB8 port.
• To use both lines of the TB8 port, short pin #3-#4 of the jumper block J104 (default

setting: #1-#2 short).

• To connect the control unit to processor unit, use the cable assy. (type: BD-07AF-

FM-LR-150).

• To connect the control units in a daisy chain connection, use the optional cable as-

sy. (type: BD-07AF-07AF-LR-100).

• Attach the terminator (type: BD-07AFFM-LR7001) to the port not used on the last

control unit in the series. If the terminator is not attached, the control unit may not
work properly.

• The total length of cables in a series must be within 30 m.

TB13

TB8

12

34

J104

Processor unit

Cable assy.

䋨

BD-07AFFM-LR-150

䋩

Cable assy.

䋨

BD-07AF-07AF-LR-100

䋩

Cable assy.

䋨

BD-07AF-07AF-LR-100

䋩

Cable assy.

䋨

BD-07AFFM-LR-150

䋩

Cable assy.

䋨

BD-07AF-07AF-LR-100

䋩

Cable assy.

䋨

BD-07AF-07AF-LR-100

䋩

Terminator

䋨

BD-07AFFM-LR7001

䋩

Terminator

䋨

BD-07AFFM-LR7001

䋩

T

o

tal length of cables

Max 30 m

Processor unit

TB8

䋨

#1 to #7 pin

䋩

TB8

䋨

#8 to #14 pin

䋩

«
...
108
109
110
111
112
...
»

Содержание NAVpilot 711C

















































































































































































Отзывы:

Нет отзывов