Furuno NAVpilot 711C Скачать руководство пользователя страница 106

Страница: 106 / 176

6. INSTALLATION AND WIRING

6-2

6.1.2

When FAP-7011 is replaced with FAP-7011C

The width of FAP-7011 is different from that of FAP-7011C.

When FAP-7011 is installed on a desktop

The bracket used for FAP-7011 can not be used with FAP-7011C.

When FAP-7011 is installed with the surface mount

Do one of the following according to the thickness of the bulkhead (d):

• d

10 mm:

Using the mount template at the back of this manual, open a hole for the projection
of the control unit. Modification to the mounting hole (90 mm diameter) is not re-
quired.

• 10 mm < d

20 mm:

Using the mount template at the back of this manual, open a mounting hole of 95
mm diameter, and a hole for the projection of the control unit.

When FAP-7011 is installed with the flush mount

The square mounting hole for FAP-7011 is not compatible with FAP-7011C. Prepare
the mounting board for installing FAP-7011C.

Содержание NAVpilot 711C

















































































































































































Результаты поиска

Содержание NAVpilot 711C

Отзывы:

Furuno NAVpilot 711C, Руководство оператора, Страница: 106 / 176

Результаты поиска

Содержание NAVpilot 711C

Отзывы: