Furuno NAVpilot 711C Скачать руководство пользователя страница 117

Страница: 117 / 176

7. INITIAL SETTINGS

7-5

7.4

Dockside Setup Menu

The [Dockside Setup] menu for the rudder reference unit (RRU) and Fantum Feed-
back

™

is different. To open the [Dockside Setup] menu, select [Dockside Setup] from

the [Installation Menu] window.

Note:

The [Dockside Setup] menu is not shown when [Boat Type] is set to [EVCS

Boat].

7.4.1

Dockside setup for the rudder reference unit

RRU type

1. Select the current setting for [Select RRU Type] from the

[Dockside Setup] menu then push the

Course control

knob.

2. Rotate the

Course control

knob to select a correct option then push the knob.

[Rotary(Inboard)]: For FURUNO rudder reference unit FAP-6112.
[Linear(Outboard)]: For Teleflex linear sensor AR4502.

RRU sensor alignment

1. Select [RRU Sensor Alignment] from the [Dockside Setup] menu then push the

Course control

knob.

The message shown below appears.

Select RRU Type:

Rotary (Inboard)

RRU Sensor Alignment

Air Bleeding: No

Rudder Limit Setup

Auto Rudder Limit:

Manual Rudder Limit:

Rudder Test: No

Dockside Setup

Rotary (Inboard)

Linear (Outboard)

Measure rudder center
position and confirm
displayed value is < 5

if not, adjust RRU arm or
magnet. NAVPILOT will
correct reversed PORT
& STBD indication later.
Push any key to continue

Содержание NAVpilot 711C

















































































































































































Результаты поиска

Содержание NAVpilot 711C

Отзывы:

Furuno NAVpilot 711C, Руководство оператора, Страница: 117 / 176

Результаты поиска

Содержание NAVpilot 711C

Отзывы: