Furuno NAVpilot 711C Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 176

Furuno NAVpilot 711C Скачать руководство пользователя страница 122

7. INITIAL SETTINGS

7-10

Rudder test

For power steering vessels with an engine-driven power steering pump, the engines
must be running and slightly above idle before doing this test. Also, BEFORE doing
this test, check that [Rudder Deadband] in the [Sea Trial] menu is set to [Auto].

1. Select the option for [Rudder Test] from the [Dockside Setup] menu then push the

Course control

knob.

2. Rotate the

Course control

knob to select [Yes] then push the knob.

3. Push the

Course control

knob to start the rudder test.

The rudder test automatically detects the drive unit.
• Solenoid: The test automatically continues.
• Reversible: The drive selection menu appears. Select the drive unit. Then, the

test continues.

After the test is completed, one of the following messages appears.
• Rudder Test completed. Push any key to continue.
• Rudder speed is too slow (fast) to control the vessel. The vessel may not be

controlled properly.

Note 1:

When one of the following messages appears, the rudder test could not

be completed successfully. Retry the test after resolving the problem.
•  Rudder Test Failed.
•  RUDDER ANGLE ERROR. Check drive circuit.
•  RUDDER DRIVE ERROR. Check drive circuit.

Note 2:

When the message "Deadband is too big to control the vessel. The vessel

may not be controlled properly. Please see inst manual for manual db setting.
Push any key to continue." appears, set the rudder deadband manually (see
section 7.9.2).

Drive Unit: -

Rudder Deadband: -

Rudder Speed: -

Testing Rudder-PLS Wait.
Push any key to abort

Rudder Setup And Auto Test

Drive Unit Select Menu

Drive Unit:

Unknown

Solenoid

Reversible 24V

Reversible 12V

Safe-Helm 24V

Safe-Helm 12V

«
...
120
121
122
123
124
...
»

Содержание NAVpilot 711C

















































































































































































Отзывы:

Нет отзывов