Furuno NAVpilot 711C Скачать руководство пользователя страница 83

Страница: 83 / 176

4. USER MENU

4-7

4.4

Course After Operation of a Remote Controller

Select the course to follow after a remote controller is operated.

Note:

This feature is not available with Fantum Feedback

™

1. In the AUTO mode, long press the

key to open the menu.

2. Rotate the

Course control

knob to select the current setting for [Cse After Re-

mote] then push the knob.
[Cse After Remote] also appears on the [AUTO Option] menu.

3. Rotate the

Course control

knob to select desired option then push the knob.

[Previous Course]: Keep the course before the operation of a remote controller.
[Present Course]: Keep the course after the operation of a remote controller.

4. Press the

key to close the menu.

[Cse After Remote] = [Previous Course]

[Cse After Remote] = [Present Course]

Previous course

Remote
controller: OFF
Remote
controller: ON

Previous course

New course

Remote
controller: ON

Remote
controller: OFF

Previous Course

Present Course

Содержание NAVpilot 711C

















































































































































































Результаты поиска

Содержание NAVpilot 711C

Отзывы:

Furuno NAVpilot 711C, Руководство оператора, Страница: 83 / 176

Результаты поиска

Содержание NAVpilot 711C

Отзывы: