manualshive.com logo in svg

Furuno NAVpilot 711C, Руководство оператора, Страница: 151 / 176

Поделиться
Скачать
Furuno NAVpilot 711C Скачать руководство пользователя страница 151

7.  INITIAL SETTINGS

7-39

7.11.3

Speed calculation

Speed is normally entered automatically, from your navigator. If the navigator fails, 
manually enter speed.

1. Rotate the 

Course control

 knob to select the current setting for [Speed Calcula-

tion] from the [Parameter Setup] menu then push the knob.

2. Rotate the 

Course control

 knob to select [Auto] or [Manual] then push the knob. 

3. For [Manual], do as follows:

1) Rotate 

the 

Course control

 knob to select the current setting value then push 

the knob.

2) Rotate 

the 

Course control

 knob to set a value then push the knob (setting 

range: 0.1 - 99.0).

7.12

AUTO Option Menu

The various features for the AUTO mode are set up from the [AUTO Option] menu. To 
open the [AUTO Option] menu, select [AUTO Option] from the [Installation Menu] win-
dow.

Item

Description

Settings

[Advanced AUTO]

The AUTO mode will maintain a set course, but your ves-
sel’s course may be shifted by the effects of tide and 
wind. To compensate for the effects of tide and wind, set 
[Advanced AUTO] to [ON]. Your NAVpilot must be con-
nected to a GPS navigator which outputs position data 
(Latitude and Longitude) in CAN bus or NMEA0183 for-
mat.862

[OFF], [ON]

[Net Towing AUTO] When a boat is towing fishing gear its stern is “dragged” 

by the net. This causes the boat to stray from its intended 
course. To keep the boat on course, your need to adjust 
the trim manually, which can be bothersome. If you do 
not want to be bothered with trim adjustments, your can 
enable the automatic towing function to have the trim au-
tomatically adjusted. This feature is useful for trawlers 
and purse seiners. This feature is not available for a sail-
boat or Fantum Feedback

™

.

[OFF], [ON]

[Cse After Remote]

Select the course to follow after a remote controller is op-
erated. [Cse After Remote] is not shown in case of Fan-
tum Feedback

™

.

[Previous Course],
[Present Course]

Other than Fantum Feedback

TM

*: Not shown with a sailboat.

Advanced Auto: 

ON

Net Towing AUTO*: OFF

Cse After Remote: Present Course

AUTO Option

Advanced Auto: 

ON

AUTO Option

For Fantum Feedback

TM

Содержание NAVpilot 711C

















































































































































































Отзывы:

Нет отзывов