Furuno NAVpilot 711C Скачать руководство пользователя страница 128

Страница: 128 / 176

7. INITIAL SETTINGS

7-16

6. Push the

Course control

knob to show the helm sensor test result.

7. Press the

key to finish the helm sensor test.

Safe helm setup (for Accu-Steer FPS 12V (or 24V) drive)

Perform the helm sensor test before doing the safe helm setup. For details of the helm
sensor test, see "Helm sensor test (for Accu-Steer FPS 12V (or 24V)
drive)" on page 7-15.

1. Select [Safe Helm/P.Assist Setup] from the [Dockside Setup] menu then push the

Course control

knob.

[Safe Helm/P.Assist Setup] appears on the [Dockside Setup] menu after the helm
sensor test is successfully completed.

2. Rotate the

Course control

knob to select the current setting for [Safe Helm] then

push the knob.

3. Rotate the

Course control

knob to select [ON] then push the knob to activate the

safe helm.

4. Rotate the

Course control

knob to select the current setting value for [Return De-

lay] then push the knob.

5. Rotate the

Course control

knob to set a value for [Return Delay] then push the

knob (setting range: 1-20 sec.).
•

NAV mode

: When the data from the helm sensor is not input for the set time,

NAV mode is restored.

•

Other than NAV mode)

: When cruising straight ahead and the data from the

helm sensor is not input for the set time, the previous steering mode is restored.

Universal Input1: STBD*

Universal Input2: PORT*

Helm Sensor Test

Push MENU key to return.

Not shown with Fantum Feedback

*: “--” appears if the test failed.

Safe Helm:

Return Delay 5 sec

Safe Helm Response

Safe Helm Beep: ON

Power Assist: OFF

Safe Helm/P.Assist Setup

Содержание NAVpilot 711C

















































































































































































Результаты поиска

Содержание NAVpilot 711C

Отзывы:

Furuno NAVpilot 711C, Руководство оператора, Страница: 128 / 176

Результаты поиска

Содержание NAVpilot 711C

Отзывы: