Furuno NAVpilot 711C Скачать руководство пользователя страница 107

Страница: 107 / 176

6. INSTALLATION AND WIRING

6-3

6.1.3

How to install the control unit

1. Detach the nut lock then unfasten the toothed nut.

2. Using the mount template at the back of this manual, open a mounting hole in the

installation site.

Note:

According to the bulkhead thickness (d), the diameter of the mounting hole

changes as follows:
• d

10 mm: Open a mounting hole of 90 mm in diameter.

• 10 mm < d

20 mm: Open a mounting hole of 95 mm in diameter.

3. Attach the surface mount sponge to the mounting location.

Fit the notch of the sponge with the hole for the projection of the control unit to
prevent the sponge from blocking the hole.

4. Set the unit to the mounting hole.

Toothed nut

Nut lock

Control unit

The rear side of the control unit FAP-7011C

Hole for the projection

Notch

Surface mount sponge

Mounting hole

Содержание NAVpilot 711C

















































































































































































Результаты поиска

Содержание NAVpilot 711C

Отзывы:

Furuno NAVpilot 711C, Руководство оператора, Страница: 107 / 176

Результаты поиска

Содержание NAVpilot 711C

Отзывы: