Furuno NAVpilot 711C Скачать руководство пользователя страница 136

Страница: 136 / 176

7. INITIAL SETTINGS

7-24

5. Press the

key to return to the [CAN Bus Setup] menu.

6. Rotate the

Course control

knob to select [Select Output PGN List] then push the

knob.

This display shows all the NMEA 2000 PGNs that can be output to the connected
NMEA 2000 network. The sentences selected for output show “ON“. To turn a
sentence ON or OFF, go to step 7. If you do not need to change the settings, go
to step 8.

Note:

Turn OFF the sentence “127245“ (rudder) in case of Fantum Feedback

™

7. To turn an NMEA 2000 sentence ON or OFF, do the following:

1) Rotate

the

Course control

knob to select a sentence then push the knob.

2) Rotate

the

Course control

knob to select [ON] or [OFF] then push the knob.

8. Press the

key to return to the [CAN Bus Setup] menu.

9. Rotate the

Course control

knob to select the option for [Refresh] then push the

knob.

10. Rotate the

Course control

knob to select [Yes] then push the knob.

After five seconds, the [Devise List] display is refreshed.

CAN Bus

127237: ON

127250: OFF

127258: OFF

128267: OFF

126992:

OFF

127245: OFF

127251: OFF

128259: OFF

*: The PGN title of the selected PGN is displayed.

System Time*

Содержание NAVpilot 711C

















































































































































































Результаты поиска

Содержание NAVpilot 711C

Отзывы:

Furuno NAVpilot 711C, Руководство оператора, Страница: 136 / 176

Результаты поиска

Содержание NAVpilot 711C

Отзывы: