manualshive.com logo in svg

Fujitsu MHS2020AT, Руководство по эксплуатации продукта

Fujitsu MHS2020AT - вибрісний жорсткий диск від Fujitsu з ємністю 20 ГБ. Для отримання докладної інструкції з використання ви можете завантажити безкоштовний посібник користувача з manualshive.com. Натисніть "Download" на сайті для збереження.

Поделиться
Скачать
background image

C141-E171-03EN

GL-1

Glossary

Actuator

Head positioning assembly.  The actuator consists of a voice coil motor and head
arm.  If positions the read-write (R-W) head.

AT bus

A bus between the host CPU and adapter board

ATA (AT Attachment) standard

The ATA standard is for a PC AT interface regulated to establish compatibility
between products manufactured by different vendors.  Interfaces based on this
standard are called ATA interfaces.

BIOS standard for drives

The BIOS standard collectively refers to the parameters defined by the host,
which, for example, include the number of cylinders, the number of heads, and
the number of sectors per track in the drive.  The physical specifications of the
drive do not always correspond to these parameters.

The BIOS of a PC AT cannot make full use of the physical specifications of these
drivers.  To make the best use of these drives, a BIOS that can handle the standard
parameters of these drives is required.

Command

Commands are instructions to input data to and output data from a drive.
Commands are written in command registers.

Data block

A data block is the unit used to transfer data.  A data block normally indicates a
single sector.

DE

Disk enclosure.  The DE includes the disks, built-in spindle motor, actuator,
heads, and air filter.  The DE is sealed to protect these components from dust.

Master (Device 0)

The master is the first drive that can operate on the AT bus.  The master is daisy-
chained with the second drive which can operate in conformity with the ATA
standard.

Содержание MHS2020AT































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHS2020AT

Navigloo 3120 Assembly Instructions Manual preview
3120
Бренд: Navigloo Страницы: 28
Arrow Storage Products 697.68222 Owner'S Manual & Assembly Instructions preview
697.68222
Бренд: Arrow Storage Products Страницы: 34
Quantum DLT 2500 Product Manual preview
DLT 2500
Бренд: Quantum Страницы: 345
Oki 70043502 Installation Instructions Manual preview
70043502
Бренд: Oki Страницы: 16
AIC SB302-LB User Manual preview
SB302-LB
Бренд: AIC Страницы: 101
Tandberg Data REPLACE TAPE DRIVE IN STORAGELOADER VXA... Manual preview
REPLACE TAPE DRIVE IN STORAGELOADER VXA...
Бренд: Tandberg Data Страницы: 10
dallmeier DAS-300 E Installation And Commissioning Manual preview
DAS-300 E
Бренд: dallmeier Страницы: 32
Quantum ATL 7100 Operator'S Manual preview
ATL 7100
Бренд: Quantum Страницы: 78
Netstor NA380A-G3 User Manual preview
NA380A-G3
Бренд: Netstor Страницы: 11
Hitachi HTS723212L9A360 Specifications preview
HTS723212L9A360
Бренд: Hitachi Страницы: 176
Hitachi HTS723212L9A360 Install Manual preview
HTS723212L9A360
Бренд: Hitachi Страницы: 5
Cisco MEM2600-16D Configuration Note preview
MEM2600-16D
Бренд: Cisco Страницы: 18
Cisco MDS 9509 Datasheet preview
MDS 9509
Бренд: Cisco Страницы: 8
Cisco MEM-C6KNAM-2GB Upgrade Installation preview
MEM-C6KNAM-2GB
Бренд: Cisco Страницы: 20
Cisco CSS8-IDM-MEM-HD Quick Start Manual preview
CSS8-IDM-MEM-HD
Бренд: Cisco Страницы: 4
Cisco NSS 300 Series Brochure & Specs preview
NSS 300 Series
Бренд: Cisco Страницы: 2
Cisco Memory Card MEMCUE-256D= Installation Manual preview
Memory Card MEMCUE-256D=
Бренд: Cisco Страницы: 8
Cisco NSS 324 Quick Start Manual preview
NSS 324
Бренд: Cisco Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды