manualshive.com logo in svg

Fujitsu MHS2020AT, Руководство по эксплуатации продукта

Fujitsu MHS2020AT - вибрісний жорсткий диск від Fujitsu з ємністю 20 ГБ. Для отримання докладної інструкції з використання ви можете завантажити безкоштовний посібник користувача з manualshive.com. Натисніть "Download" на сайті для збереження.

Поделиться
Скачать
background image

Glossary

GL-2

C141-E171-03EN

MTBF

Mean time between failures.  The MTBF is calculated by dividing the total
operation time (total power-on time) by the number of failures in the disk drive
during operation.

MTTR

Mean time to repair.  The MTTR is the average time required for a service person
to diagnose and repair a faulty drive.

PIO (Programmed input-output)

Mode to transfer data under control of the host CPU

Positioning

Sum of the seek time and mean rotational delay

Power save mode

The power save modes are idle mode, standby mode, and sleep mode.

In idle mode, the drive is neither reading, writing, nor seeking data.  In standby
mode, the spindle motor is stopped and circuits other than the interface control
circuit are sleeping.  The drive enters sleep mode when the host issues the SLEEP
command.

Reserved

Reserved bits, bytes, and fields are set to zero and unusable because they are
reserved for future standards.

Rotational delay

Time delay due to disk rotation.  The mean delay is the time required for half a
disk rotation.  The mean delay is the average time required for a head to reach a
sector after the head is positioned on a track.

Seek time

The seek time is the time required for a head to move from the current track to
another track.  The seek time does not include the mean rotational delay.

Slave (Device 1)

The slave is a second drive that can operate on the AT bus.  The slave is daisy-
chained with the first drive operating in conformity with the ATA standard.

Содержание MHS2020AT































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHS2020AT

WATSON SEVEN Assembly Instructions Manual preview
SEVEN
Бренд: WATSON Страницы: 12
LaCie 301200U User Manual preview
301200U
Бренд: LaCie Страницы: 48
G&T SALES Fast Framer Quick Start Manual preview
Fast Framer
Бренд: G&T SALES Страницы: 2
IBM Travelstar 14GS Quick Installation Manual preview
Travelstar 14GS
Бренд: IBM Страницы: 2
Tandberg Data STORAGE CAB4000 - Quick Install Manual preview
STORAGE CAB4000 -
Бренд: Tandberg Data Страницы: 13
Riverlea SmartStore SM2015 Assembly Instructions Manual preview
SmartStore SM2015
Бренд: Riverlea Страницы: 16
kincrome K7308 Operation Manual preview
K7308
Бренд: kincrome Страницы: 3
garofalo TUSCANY 240 User Manual preview
TUSCANY 240
Бренд: garofalo Страницы: 20
IBM Travelstar 10E Installation And Operation Manual preview
Travelstar 10E
Бренд: IBM Страницы: 11
Netstor NA762TB3 User Manual preview
NA762TB3
Бренд: Netstor Страницы: 17
Netstor NA380A-G3 User Manual preview
NA380A-G3
Бренд: Netstor Страницы: 11
Seville Classics UltraHD 20206 Assembly Instructions Manual preview
UltraHD 20206
Бренд: Seville Classics Страницы: 7
Dell PowerVault Manual preview
PowerVault
Бренд: Dell Страницы: 396
Dell PowerVault 600 Getting Started preview
PowerVault 600
Бренд: Dell Страницы: 180
Dell EqualLogic PS6010 Hardware Maintenance preview
EqualLogic PS6010
Бренд: Dell Страницы: 57
Dell PowerVault 700N Administrator'S Manual preview
PowerVault 700N
Бренд: Dell Страницы: 29
Dell PowerEdge M830 Owner'S Manual preview
PowerEdge M830
Бренд: Dell Страницы: 133
SECUDRIVE USB Basic User Manual preview
USB Basic
Бренд: SECUDRIVE Страницы: 29

Бренды по названию

Популярные бренды

Загрузить еще бренды