manualshive.com logo in svg

Fujitsu MHS2020AT, Руководство по эксплуатации продукта

Fujitsu MHS2020AT - вибрісний жорсткий диск від Fujitsu з ємністю 20 ГБ. Для отримання докладної інструкції з використання ви можете завантажити безкоштовний посібник користувача з manualshive.com. Натисніть "Download" на сайті для збереження.

Поделиться
Скачать
background image

6.3  Defect Processing

C141-E171-03EN

6-9

6.2.2 Power commands

The following commands are available as power commands.

•

 

IDLE

•

 

IDLE IMMEDIATE

•

 

STANDBY

•

 

STANDBY IMMEDIATE

•

 

SLEEP

•

 

CHECK POWER MODE

•

 

SET FEATURES (APM setting)

6.3 Defect Processing

This device performs alternating processing where the defective sector is
alternated with the spare area depending on media defect location information.
The media defect location information is registered in the system space specified
for the user area according to the format at shipment of the media from the plant.

6.3.1 Spare area

The following two types of areas are prepared as the spare area in user areas:

1)

Spare area for sector slip:  At shipment of the media from the plant, this area
is defined for use in alternating processing for defective sectors during format
processing.  254 sectors/128 tracks.

2)

Spare cylinder for alternate assignment:  This cylinder is used during
automatic alternating processing for defective sector.  2000 sectors/drive.

Содержание MHS2020AT































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHS2020AT

WATSON SEVEN Assembly Instructions Manual preview
SEVEN
Бренд: WATSON Страницы: 12
Kingston Technology DataTraveler Locker+ Generation 3 DTLPG3 Installation Manual preview
DataTraveler Locker+ Generation 3 DTLPG3
Бренд: Kingston Technology Страницы: 1623
LaCie d2 Ethernet Disk mini Quick Install Manual preview
d2 Ethernet Disk mini
Бренд: LaCie Страницы: 23
QNAP TS-h1677XU-RP Quick Installation Manual preview
TS-h1677XU-RP
Бренд: QNAP Страницы: 7
Synology DS3611xs Quick Installation Manual preview
DS3611xs
Бренд: Synology Страницы: 26
Hanover HGS001 Series Assembly & Care Manual preview
HGS001 Series
Бренд: Hanover Страницы: 12
Performance Tool W5184 Owner'S Manual preview
W5184
Бренд: Performance Tool Страницы: 2
Seagate Expansion STEB6000403 Quick Start Manual preview
Expansion STEB6000403
Бренд: Seagate Страницы: 5
Asus Travelair-AC User Manual preview
Travelair-AC
Бренд: Asus Страницы: 32
Asus EHD-A1T Quick Start Manual preview
EHD-A1T
Бренд: Asus Страницы: 40
Asus WL-HDD User Manual preview
WL-HDD
Бренд: Asus Страницы: 58
Asus FrontLinker User Manual preview
FrontLinker
Бренд: Asus Страницы: 10
Asus Zendisk AS400 User Manual preview
Zendisk AS400
Бренд: Asus Страницы: 8
Asus Leather External HDD USB 3.0 User Manual preview
Leather External HDD USB 3.0
Бренд: Asus Страницы: 2
Asus FlexSave User Manual preview
FlexSave
Бренд: Asus Страницы: 14
Asus Travelair N User Manual preview
Travelair N
Бренд: Asus Страницы: 21
Asus AN200 External HDD User Manual preview
AN200 External HDD
Бренд: Asus Страницы: 2
Asus AR200 User Manual preview
AR200
Бренд: Asus Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды