Fujitsu MHS2020AT Скачать руководство пользователя страница 197 | Manualshive

Страница: 197 / 254

background image

5.5 Ultra DMA Feature Set

C141-E171-03EN

5-121

5.5.4 Ultra DMA data out commands

5.5.4.1 Initiating an Ultra DMA data out burst

The following steps shall occur in the order they are listed unless otherwise
specifically allowed (see 5.6.3.7 and 5.6.3.2 for specific timing requirements):

1)

The host shall keep DMACK- in the negated state before an Ultra DMA burst
is initiated.

2)

The device shall assert DMARQ to initiate an Ultra DMA burst.

3)

Steps (3), (4), and (5) may occur in any order or at the same time. The host
shall assert STOP.

4)

The host shall assert HSTROBE.

5)

The host shall negate CS0-, CS1-, DA2, DA1, and DA0. The host shall keep
CS0-, CS1-, DA2, DA1, and DA0 negated until after negating DMACK- at
the end of the burst.

6)

Steps (3), (4), and (5) shall have occurred at least t

ACK

before the host asserts

DMACK-. The host shall keep DMACK- asserted until the end of an Ultra
DMA burst.

7)

The device may negate DDMARDY- t

ZIORDY

after the host has asserted

DMACK-. Once the device has negated DDMARDY-, the device shall not
release DDMARDY- until after the host has negated DMACK- at the end of
an Ultra DMA burst.

8)

The host shall negate STOP within t

ENV

after asserting DMACK-. The host

shall not assert STOP until after the first negation of HSTROBE.

9)

The device shall assert DDMARDY- within t

LI

after the host has negated

STOP. After asserting DMARQ and DDMARDY- the device shall not
negate either signal until after the first negation of HSTROBE by the host.

10) The host shall drive the first word of the data transfer onto DD (15:0). This

step may occur any time during Ultra DMA burst initiation.

11) To transfer the first word of data: the host shall negate HSTROBE no sooner

than t

LI

after the device has asserted DDMARDY-. The host shall negate

HSTROBE no sooner than t

DVS

after the driving the first word of data onto

DD (15:0).

5.5.4.2 The data out transfer

The following steps shall occur in the order they are listed unless otherwise
specifically allowed (see 5.6.3.8 and 5.6.3.2 for specific timing requirements):

1)

The host shall drive a data word onto DD (15:0).

«
...
195
196
197
198
199
...
»

Содержание MHS2020AT































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHS2020AT

Бренд: G-Technology Страницы: 51

01OVLPA0806SDFW-V1

Бренд: Walton Страницы: 6

Rugged Triple USB 3.0

Бренд: LaCie Страницы: 2

Rugged Triple USB 3.0

Бренд: LaCie Страницы: 2

Бренд: LaCie Страницы: 5

RUGGED BOSS SSD

Бренд: LaCie Страницы: 60

Бренд: LaCie Страницы: 2

Little Big Disk Quadra

Бренд: LaCie Страницы: 4

Little Big Disk Quadra

Бренд: LaCie Страницы: 24

Бренд: LaCie Страницы: 53

Бренд: LaCie Страницы: 59

5BIG THUNDERBOLT 2

Бренд: LaCie Страницы: 54

Starck Desktop Hard Drive

Бренд: LaCie Страницы: 2

Бренд: LaCie Страницы: 24

Бренд: LaCie Страницы: 52

Rugged Hard Disk

Бренд: LaCie Страницы: 2

Network Space MAX

Бренд: LaCie Страницы: 2

Rugged Hard Disk

Бренд: LaCie Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды