Fujitsu MHS2020AT Скачать руководство пользователя страница 33

Страница: 33 / 254

1.8 Error Rate

C141-E171-03EN

1-13

Active Idle:

The head is in a position of extreme inner in disk medium.
(VCM Lock)

Low power Idle:

The head is unloaded from disk. (VCM Unload)
The spindle motor rotates.

Standby:

The spindle motor stops.

APM Mode

Active Idle

(VCM Lock)

Low Power Idle

(VCM Unload)

Standby

(Spin Off)

Mode-0

3sec

N/A

Mode-1

3sec

10sec

N/A

Mode-2

3sec

4sec

60sec

Mode-0: It shifts to Active Idle in 3 seconds from the Idle condition.
Mode-1: It shifts to Low power Idle in 13 seconds from the Idle condition.
Mode-2: It shifts to Standby in 67 seconds from the Idle condition.

* The set point is reflected on WORD91 of the IDENTITY DEVICE command.

APM mode is returned to Default due to hard resetting or the power off.

Содержание MHS2020AT































































































































































































































































Результаты поиска

Содержание MHS2020AT

Отзывы:

Fujitsu MHS2020AT, Руководство по эксплуатации продукта, Страница: 33 / 254

Результаты поиска

Содержание MHS2020AT

Отзывы: