Fujitsu MHS2020AT Скачать руководство пользователя страница 228 | Manualshive

Страница: 228 / 254

background image

Operations

6-10

C141-E171-03EN

6.3.2 Alternating processing for defective sectors

The following two types of technology are used for alternating processing:

(1) Sector slip processing

In this method, defective sectors are not used (thereby avoiding the effects of
defects), and each defective sector is assigned to the next contiguous sector that is
normal.

Depending on the format defined at shipment from the plant, this processing is
performed for defective sectors.

Figure 6.5 shows an example where sector (physical) 5 with cylinder 0 and head 0
is defective.

Sector (physical)

Cylinder 0
Head 0

Defec-
tive
sector

(Not used)

Note: When an access request for sector 5 is issued, physical sector 6 must be

accessed instead of physical sector 5.

Figure 6.5 Sector slip processing

(2) Alternate cylinder assignment processing

This technology assigns a defective sector to a spare sector of an alternate
cylinder.

This processing is performed when automatic alternating processing is attempted
for a physical track that contains three or more defective sectors.

Figure 6.6 shows an example where alternate cylinder assignment processing is
applied to sector (physical) 5 with cylinder 0 and head 0.

«
...
226
227
228
229
230
...
»

Содержание MHS2020AT































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHS2020AT

Бренд: IAC INDUSTRIES Страницы: 8

Бренд: Backyard Discovery Страницы: 43

Бренд: Backyard Products Страницы: 72

Бренд: Seagate Страницы: 24

2,5" EXTERNAL HARD DRIVE KIT

Бренд: Intenso Страницы: 94

Бренд: i3 International Страницы: 89

Бренд: Muscle Rack Страницы: 2

Бренд: Compaq Страницы: 139

Бренд: U.S. General Страницы: 8

Save2Data SecureKey

Бренд: Hama Страницы: 38

Бренд: Yardmaster Страницы: 20

DURAMAXX 6 Ft Eco Pent Roof

Бренд: USP Страницы: 54

Бренд: U-Line Страницы: 6

Бренд: Quantum Страницы: 4

SuperLoader 3A Series

Бренд: Quantum Страницы: 121

Бренд: Spectra Logic Страницы: 21

T-Series Spectra T200

Бренд: Spectra Logic Страницы: 110

Бренд: Spectra Страницы: 184

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды