Fujitsu MHS2020AT Скачать руководство пользователя страница 120

Страница: 120 / 254

Interface

5-44

C141-E171-03EN

Table 5.5 Features register values and settable modes

Features
Register

Drive operation mode

X’02’

Enables the write cache function.

X’03’

Set the data transfer mode. *1

X’05’

Enables the advanced power management function. *2

X’42’

Enables the Acoustic management function. *3

X’55’

Disables read cache function.

X’66’

Disables the reverting to power-on default settings after software reset.

X’82’

Disables the write cache function.

X’85’

Set the advanced power management mode to the default mode.

X’AA’

Enables the read cache function.

X’BB’

Specifies the transfer of 4-byte ECC for READ LONG and WRITE LONG
commands.

X’C2’

Disables the Acoustic management function.

X’CC’

Enables the reverting to power-on default settings after software reset. (*1)

*1 Although there is a response to the command, nothing is done.

At power-on or after hardware reset, the default mode is set as follows.

Write cashe function

: Enabled

Transfer mode

: PIO Mode-4, Multiworld DMA Mode-2

Advanced power
management function

: Enabled (Mode-1)

Acoustic
management function

: Disabled (Standard Seek)

Read cashe function

: Enabled

Default setting
after software reset

: Disabled

Содержание MHS2020AT































































































































































































































































Результаты поиска

Содержание MHS2020AT

Отзывы:

Похожие инструкции для MHS2020AT

Бренды по названию

Популярные бренды

Fujitsu MHS2020AT, Руководство по эксплуатации продукта

Результаты поиска

Содержание MHS2020AT

Отзывы:

Похожие инструкции для MHS2020AT

Бренды по названию

Популярные бренды