Fujitsu MHS2020AT Скачать руководство пользователя страница 198 | Manualshive

Страница: 198 / 254

background image

Interface

5-122

C141-E171-03EN

2)

The host shall generate an HSTROBE edge to latch the new word no sooner
than t

DVS

after changing the state of DD (15:0). The host shall generate an

HSTROBE edge no more frequently than t

CYC

for the selected Ultra DMA

Mode. The host shall not generate two rising or falling HSTROBE edges
more frequently than 2 t

CYC

for the selected Ultra DMA mode.

3)

The host shall not change the state of DD (15:0) until at least t

DVH

after

generating an HSTROBE edge to latch the data.

4)

The host shall repeat steps (1), (2) and (3) until the data transfer is complete
or an Ultra DMA burst is paused, whichever occurs first.

5.5.4.3 Pausing an Ultra DMA data out burst

The following steps shall occur in the order they are listed unless otherwise
specifically allowed (see 5.6.3.9 and 5.6.3.2 for specific timing requirements).

a)

Host pausing an Ultra DMA data out burst

1)

The host shall not pause an Ultra DMA burst until at least one data word
of an Ultra DMA burst has been transferred.

2)

The host shall pause an Ultra DMA burst by not generating an
HSTROBE edge.

Note: The device shall not immediately negate DMARQ to initiate Ultra

DMA burst termination when the host stops generating
HSTROBE edges. If the host does not assert STOP, in order to
initiate Ultra DMA burst termination, the device shall negate
DDMARDY- and wait t

RP

before negating DMARQ.

3)

The host shall resume an Ultra DMA burst by generating an HSTROBE
edge.

b)

Device pausing an Ultra DMA data out burst

1)

The device shall not pause an Ultra DMA burst until at least one data
word of an Ultra DMA burst has been transferred.

2)

The device shall pause an Ultra DMA burst by negating DDMARDY-.

3)

The host shall stop generating HSTROBE edges within t

RFS

of the device

negating DDMARDY-.

4)

If the device negates DDMARDY- within t

SR

after the host has generated

an HSTROBE edge, then the device shall be prepared to receive zero or
one additional data words. If the device negates DDMARDY- greater
than t

SR

after the host has generated an HSTROBE edge, then the device

shall be prepared to receive zero, one or two additional data words. The
additional data words are a result of cable round trip delay and t

RFS

timing

for the host.

5)

The device shall resume an Ultra DMA burst by asserting DDMARDY-.

«
...
196
197
198
199
200
...
»

Содержание MHS2020AT































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHS2020AT

Бренд: LaCie Страницы: 22

Бренд: Maxtor Страницы: 73

Бренд: iStorage Страницы: 2

Бренд: Premio Страницы: 2

Бренд: iStorage Страницы: 23

Бренд: Yardmaster Страницы: 20

Expansion STEB6000403

Бренд: Seagate Страницы: 5

Бренд: D-Link Страницы: 69

ShareCenter Pro DNS-1200-05

Бренд: D-Link Страницы: 170

Бренд: MCE Technologies Страницы: 19

Бренд: Eyefi Страницы: 2

Бренд: Measurement Computing Страницы: 29

Rugged Triple USB 3.0

Бренд: LaCie Страницы: 24

Бренд: Adaptec Страницы: 2

RAIDstation RS/7U160 KIT

Бренд: Adaptec Страницы: 51

RAIDStation RS/7F

Бренд: Adaptec Страницы: 53

Бренд: ECOSAFE Страницы: 7

Бренд: Crosley Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды