manualshive.com logo in svg

Fujitsu MHS2020AT, Руководство по эксплуатации продукта, Страница: 180 / 254

Поделиться
Скачать
Fujitsu MHS2020AT Скачать руководство пользователя страница 180

Interface

5-104

C141-E171-03EN

5.3.3 Error posting

Table 5.17 lists the defined errors that are valid for each command.

Table 5.17 Command code and parameters (1 of 2)

Command name

Error register (X’1F1’)

Status register (X’1F7’)

ICRC

UNC

INDF

ABRT

TK0NF

DRDY

DWF

ERR

READ SECTOR(S)

V

V

V

V

V

V

WRITE SECTOR(S)

V

V

V

V

V

READ  MULTIPLE

V

V

V

V

V

V

WRITE MULTIPLE

V

V

V

V

V

READ DMA

V

V

V

V

V

V

V

WRITE  DMA

V

V

V

V

V

V

WRITE VERIFY

V

V

V

V

V

V

READ VERIFY SECTOR(S)

V

V

V

V

V

V

RECALIBRATE

V

V

V

V

V

SEEK

V

V

V

V

V

INITIALIZE DEVICE PARAMETERS

V

V

V

V

IDENTIFY DEVICE

V

V

V

V

IDENTIFY DEVICE DMA

V

V

V

V

SET FEATURES

V

V

V

V

SET MULTIPLE MODE

V

V

V

V

SET MAX ADDRESS

V

V

V

V

V

READ NATIVE MAX ADDRESS

V

V

V

V

EXECUTE DEVICE DIAGNOSTIC

*1

*1

*1

*1

*1

V

READ LONG

V

V

V

V

V

WRITE LONG

V

V

V

V

V

READ BUFFER

V

V

V

V

WRITE BUFFER

V

V

V

V

IDLE

V

V

V

V

IDLE IMMEDIATE

V

V

V

V

STANDBY

V

V

V

V

STANDBY IMMEDIATE

V

V

V

V

V:

Valid on this command

*1:

See the command descriptions.

*2:

Valid only for Ultra DMA command.

Содержание MHS2020AT































































































































































































































































Отзывы:

Нет отзывов