Fujitsu MHS2020AT Скачать руководство пользователя страница 192 | Manualshive

Страница: 192 / 254

background image

Interface

5-116

C141-E171-03EN

device compares its CRC data to the data sent from the host. If the two values do
not match the device reports an error in the error register at the end of the
command. If an error occurs during one or more Ultra DMA bursts for any one
command, at the end of the command, the device shall report the first error that
occurred.

5.5.2 Phases of operation

An Ultra DMA data transfer is accomplished through a series of Ultra DMA data
in or data out bursts. Each Ultra DMA burst has three mandatory phases of
operation: the initiation phase, the data transfer phase, and the Ultra DMA burst
termination phase. In addition, an Ultra DMA burst may be paused during the
data transfer phase (see 5.5.3 and 5.5.4 for the detailed protocol descriptions for
each of these phases, 5.6 defines the specific timing requirements). In the
following rules DMARDY- is used in cases that could apply to either
DDMARDY- or HDMARDY-, and STROBE is used in cases that could apply to
either DSTROBE or HSTROBE. The following are general Ultra DMA rules.

a)

An Ultra DMA burst is defined as the period from an assertion of DMACK-
by the host to the subsequent negation of DMACK-.

b)

A recipient shall be prepared to receive at least two data words whenever it
enters or resumes an Ultra DMA burst.

5.5.3 Ultra DMA data in commands

5.5.3.1 Initiating an Ultra DMA data in burst

The following steps shall occur in the order they are listed unless otherwise
specifically allowed (see 5.6.3.1 and 5.6.3.2 for specific timing requirements):

1)

The host shall keep DMACK- in the negated state before an Ultra DMA burst
is initiated.

2)

The device shall assert DMARQ to initiate an Ultra DMA burst. After
assertion of DMARQ the device shall not negate DMARQ until after the first
negation of DSTROBE.

3)

Steps (3), (4) and (5) may occur in any order or at the same time. The host
shall assert STOP.

4)

The host shall negate HDMARDY-.

5)

The host shall negate CS0-, CS1-, DA2, DA1, and DA0. The host shall keep
CS0-, CS1-, DA2, DA1, and DA0 negated until after negating DMACK- at
the end of the burst.

6)

Steps (3), (4) and (5) shall have occurred at least t

ACK

before the host asserts

DMACK-. The host shall keep DMACK- asserted until the end of an Ultra
DMA burst.

7)

The host shall release DD (15:0) within t

AZ

after asserting DMACK-.

«
...
190
191
192
193
194
...
»

Содержание MHS2020AT































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHS2020AT

301160U - 1TB Ethernet Disk RAID Network Attached...

Бренд: LaCie Страницы: 5

Бренд: LaCie Страницы: 6

Бренд: U-Line Страницы: 3

Бренд: QNAP Страницы: 63

Бренд: CASARIA Страницы: 13

Бренд: SmartStore Страницы: 16

Бренд: Netstor Страницы: 17

ST9160511NS - Constellation 7200 160 GB Hard Drive

Бренд: Seagate Страницы: 46

Бренд: TrekStor Страницы: 48

Бренд: Black & Decker Страницы: 14

Workmate 79-020

Бренд: Black & Decker Страницы: 8

Бренд: Black & Decker Страницы: 20

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 8

Бренд: Black & Decker Страницы: 10

Бренд: Black & Decker Страницы: 12

Workmate 425 TYPE 5

Бренд: Black & Decker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды