Fujitsu MHS2020AT Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 254

background image

5.3 Host Commands

C141-E171-03EN

5-19

CM: Command register

FR: Features register

DH: Device/Head register

ST: Status register

CH: Cylinder High register

ER: Error register

CL: Cylinder Low register

L: LBA (logical block address) setting bit

SN: Sector Number register

DV: Device address. bit

SC: Sector Count register

x, xx: Do not care (no necessary to set)

Note:

1.

When the L bit is specified to 1, the lower 4 bits of the DH register and all
bits of the CH, CL and SN registers indicate the LBA bits (bits of the DH
register are the MSB (most significant bit) and bits of the SN register are
the LSB (least significant bit).

2.

At error occurrence, the SC register indicates the remaining sector count of data
transfer.

3.

In the table indicating I/O registers contents in this subsection, bit indication is
omitted.

(1) READ SECTOR(S) (X’20’ or X’21’)

This command reads data of sectors specified in the Sector Count register from
the address specified in the Device/Head, Cylinder High, Cylinder Low and
Sector Number registers. Number of sectors can be specified from 1 to 256
sectors. To specify 256 sectors reading, ‘00’ is specified. For the DRQ, INTRQ,
and BSY protocols related to data transfer, see Subsection 5.4.1.

If the head is not on the track specified by the host, the device performs an
implied seek. After the head reaches to the specified track, the device reads the
target sector.

If an error occurs, retry reads are attempted to read the target sector before
reporting an error, irrespective of the R bit setting.

The DRQ bit of the Status register is always set prior to the data transfer
regardless of an error condition.

Upon the completion of the command execution, command block registers
contain the cylinder, head, and sector addresses (in the CHS mode) or logical
block address (in the LBA mode) of the last sector read.

If an unrecoverable error occurs in a sector, the read operation is terminated at the
sector where the error occurred. Command block registers contain the cylinder, the
head, and the sector addresses of the sector (in the CHS mode) or the logical
block address (in the LBA mode) where the error occurred, and remaining
number of sectors of which data was not transferred.

«
...
93
94
95
96
97
...
»

Содержание MHS2020AT































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MHS2020AT

Бренд: OEM Tools Страницы: 4

Бренд: Seagate Страницы: 36

Бренд: Xigmatek Страницы: 2

VPFEM4128GSCBMTL

Бренд: Viking Technology Страницы: 36

Бренд: Artillian Страницы: 3

MERCURY ELITE PRO MINI

Бренд: OWC Страницы: 8

Бренд: HGST Страницы: 51

Бренд: IBM Страницы: 36

Бренд: SAJ Страницы: 42

Storage Library T24

Бренд: Tandberg Data Страницы: 6

Бренд: Magnusson Страницы: 24

Бренд: myToys Страницы: 4

Бренд: Blackmagic Страницы: 326

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 50

Бренд: Sony Страницы: 124

Бренд: Sony Страницы: 136

SecureAccess SDCZ73-064G-I35

Бренд: SanDisk Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды