Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 60

Страница: 60 / 90

System expansions

Fujitsu Technology Solutions

Removing an optional port

►

Open the casing (see "Opening the casing").

►

Disconnect the cable from the connector on the mainboard.

►

Press on the locking lever in the direction of the arrow (1), unhook it and swing it up in the
direction of the arrow (2).

►

Remove the port from the slot (3).

For cooling, protection against fire, and in order to comply with EMC (electromagnetic
compatibility) regulations, you must refit the cover plate.

►

Push the rear slot cover plate into the slot (4). Ensure that the point of the cover engages on
the outside of the casing.

►

Fold the lock closed in the direction of the arrow (5) and allow it to engage.

►

Close the casing (see "Closing the casing").

Содержание ESPRIMO E5635



























































































Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Похожие инструкции для ESPRIMO E5635

Бренды по названию

Популярные бренды

Fujitsu ESPRIMO E5635, Руководство по эксплуатации

Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Похожие инструкции для ESPRIMO E5635

Бренды по названию

Популярные бренды