manualshive.com logo in svg

Fujitsu ESPRIMO E5635, Руководство по эксплуатации

Поделиться
Скачать
Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 75

 System 

expansions 

Fujitsu Technology Solutions  

67 

Replacing second hard disk in 3 ½ inch drive cage 

►

 

Open the casing (see "Opening the casing"). 

►

 

Remove the cross-piece (see "Removing the cross-piece”). 

►

 

Fold up the drive cage (see "Folding up the drive cage"). 

Removing second hard disk 

1

1

 

 

►

 

Remove the screw (1). 

►

 

Disconnect the cables from the hard 
disk. 

►

 

Remove the drive the direction of the 
arrow out of the casing. 

 

Installing second hard disk 

1

1

 

 

►

 

Slide the drive into the casing in the 
direction of the arrow. 

►

 

Secure the hard disk with the 
screws (1). 

►

 

Connect the cables. 

►

 

Fold down the drive cage (see "Folding 
down the drive cage"). 

 

►

 

If necessary, mount the plastic drive cover (see "Installing plastic drive cover"). 

►

 

Replace the cross piece (see "Installing the cross-piece"). 

►

 

Close the casing (see "Closing the casing"). 

 

i

 

It may be necessary to modify the entry for the drive in the 

BIOS Setup

. 

 

Содержание ESPRIMO E5635



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды