Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 90

background image

Preparing for use

10

Fujitsu Technology Solutions

Connecting external devices

!

Read the documentation on the external device before connecting it.
With the exception of USB devices, always remove all power plugs before connecting
external devices!
Do not connect or disconnect cables during a thunderstorm.
Always take hold of the actual plug. Never unplug a cable by pulling the cable itself.
Connect and disconnect the cables in the order described below.

Connecting cables

►

Turn off all power and equipment switches.

►

Remove all power plugs from the grounded mains outlets.

►

Plug all cables into the device and peripherals. You must observe the information provided in
the "Important notes" chapter.

►

Plug all data communication cables into the utility sockets.

►

Plug all power cables into the grounded mains outlets.

Disconnecting cables

►

Turn off all power and equipment switches.

►

Remove all power plugs from the grounded mains outlets.

►

Unplug all data communication cables from the utility sockets.

►

Unplug all cables from the device and peripherals.

i

USB devices are hot-pluggable. This means you can connect and disconnect devices
while your operating system is running.
Additional information can be found in the "Connecting external devices to the parallel or
serial port" section and in the documentation for the USB devices.

«
...
16
17
18
19
20
...
»

Содержание ESPRIMO E5635



























































































Отзывы:

Нет отзывов

Похожие инструкции для ESPRIMO E5635

Бренд: Vecow Страницы: 144

Бренд: Aaeon Страницы: 117

5694 - GT - 4 GB RAM

Бренд: Gateway Страницы: 126

ProArt PA Series

Бренд: Asus Страницы: 40

Бренд: Asus Страницы: 46

Бренд: Asus Страницы: 80

Бренд: Asus Страницы: 76

Бренд: Asus Страницы: 75

Бренд: Asus Страницы: 44

Бренд: Asus Страницы: 90

Бренд: Asus Страницы: 56

P5G43 V4-Series

Бренд: Asus Страницы: 110

Бренд: Asus Страницы: 44

Бренд: Asus Страницы: 56

Бренд: Asus Страницы: 44

Бренд: Asus Страницы: 112

Бренд: Asus Страницы: 170

Бренд: Asus Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды