Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 90

background image

System expansions

56

Fujitsu Technology Solutions

Installing and removing plastic drive covers

Removing plastic drive cover

If you install an accessible drive in the 3 ½ inch installation bay and this bay was previously empty or
contained the second hard disk, you must first remove the plastic drive cover.

►

Open the casing (see "Opening the casing").

►

Lay the casing cover accessibly on a non-slide surface.

►

Press the plastic drive cover from the inside
out of the front panel in the direction of the
arrow.

!

With some types of device you can reinstall the cover. With other types of device, the
cover is broken off and cannot be reused. However, you can purchase another cover as an
accessory, and reinstall it.
Do not throw away the safety covers. If you remove the drive again later, you must reinstall
the covers (cooling, fire protection or EMC regulations to be complied with).

«
...
62
63
64
65
66
...
»

Содержание ESPRIMO E5635



























































































Отзывы:

Нет отзывов

Похожие инструкции для ESPRIMO E5635

Бренд: Datalogic Страницы: 88

Бренд: Gateway Страницы: 278

Бренд: Texim Europe Страницы: 5

Бренд: ECS Страницы: 53

Бренд: Gateway Страницы: 126

6005 - Pro Microtower PC

Бренд: Compaq Страницы: 4

Бренд: IBM Страницы: 2

Бренд: Vivo Страницы: 3

Бренд: MSI Страницы: 53

Бренд: Dell Страницы: 84

Toughbook CF-W8EWRZZAM

Бренд: Panasonic Страницы: 2

Toughbook CF-W8EWEZZAM

Бренд: Panasonic Страницы: 2

Toughbook CF-T8EWATZJM

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 36

Toughpad FZ-M1CCAAXBM

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды