manualshive.com logo in svg

Fujitsu ESPRIMO E5635, Руководство по эксплуатации

Поделиться
Скачать
Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 52

System expansions 

 

44 

Fujitsu Technology Solutions 

Removing board from low-profile slot 

►

 

Open the casing (see "Opening the casing"). 

►

 

Disconnect the cables connected to the board.  

2

3

1

4

5

 

►

 

Press on the locking lever in the direction of the arrow (1), unhook it and swing it up in the 
direction of the arrow (2). 

►

 

Pull the board out of the slot (3). 

 

!

 

For cooling, protection against fire, and in order to comply with EMC (electromagnetic 
compatibility) regulations, you must refit the cover plate. 

 

►

 

Push the rear slot cover plate into the slot (4). Ensure that the point of the cover engages on 
the outside of the casing. 

►

 

Fold the lock closed in the direction of the arrow (5) and allow it to engage. 

►

 

Close the casing (see "Closing the casing"). 

 

i

 

If you have installed or removed a PCI board, please check the relevant PCI slot settings 
in the 

BIOS Setup

. If necessary, change the settings. Further information is provided in the 

PCI board documentation. 

 

Содержание ESPRIMO E5635



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды