Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 61

Страница: 61 / 90

System

expansions

Fujitsu Technology Solutions

Installing and removing the graphics card

The outermost slot in your device is specially designed for graphics cards (e.g. PCI Express Low
Profile).

Installing the graphics card

►

Open the casing (see "Opening the casing").

For devices with low-profile slots

►

Open the locking lever (see "Installing board in low-profile slot").

►

Pull the slot cover out of the slot in the direction of the arrow (2).

►

Push the board up to its slot (3) in the direction of the arrow as far as the stop.

►

Close the locking lever (see "Installing board in low-profile slot").

►

Close the casing (see "Closing the casing").

For devices with board bracket for long boards

►

Press on the retaining bracket in the direction of the arrow and fold it down.

►

Pull the slot cover out of the slot in the direction of the arrow (2).

►

Push the board up to its slot (3) in the direction of the arrow as far as the stop.

►

Fold the retaining bracket down again in the direction of the arrow (4). Ensure that the retaining
bracket engages.

►

Close the casing (see "Closing the casing").

Содержание ESPRIMO E5635



























































































Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu ESPRIMO E5635, Руководство по эксплуатации

Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Бренды по названию

Популярные бренды