Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 17

Страница: 17 / 90

Preparing for use

Fujitsu Technology Solutions

Vertical operating position

Proceed as follows to operate the device in the vertical operating position:

►

If necessary, disconnect the cables.

►

Position the casing vertically so that the ON/OFF switch is located at the bottom.

►

Pull off the foil from the rubber / plastic feet that you will find in the accessories package.

57 mm

6 mm

37 mm

►

Glue the rubber/plastic feet (1) on the casing wall.
In order to ensure that the device is stable, the position of the rubber/plastic feet must
correspond to the given dimensions.

►

Place the unit on the rubber / plastic feet and reconnect any cables disconnected previously.

The set-up direction is specified. The ON/OFF switch must be at the top to ensure
sufficient ventilation.

Содержание ESPRIMO E5635



























































































Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Похожие инструкции для ESPRIMO E5635

Бренды по названию

Популярные бренды

Fujitsu ESPRIMO E5635, Руководство по эксплуатации

Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Похожие инструкции для ESPRIMO E5635

Бренды по названию

Популярные бренды