Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 55

Страница: 55 / 90

System

expansions

Fujitsu Technology Solutions

►

Push the board up to its slot in the
direction of the arrow as far as the stop.

►

Press the board into the slot so that it
engages.

►

Fold up the retaining bracket so that it
engages.

►

If necessary, connect the cables.

►

Reinstall the board bracket in reverse
order as described above.

►

Replace the cross piece (see "Installing
the cross-piece").

►

Close the casing (see "Closing the
casing").

If you have installed or removed a PCI board, check the relevant PCI slot settings in the

BIOS Setup

. If necessary, change the settings. Further information is provided in the PCI

board documentation.
The upper slot is suitable for low-profile cards with an adapter.

Содержание ESPRIMO E5635



























































































Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Похожие инструкции для ESPRIMO E5635

Бренды по названию

Популярные бренды

Fujitsu ESPRIMO E5635, Руководство по эксплуатации

Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Похожие инструкции для ESPRIMO E5635

Бренды по названию

Популярные бренды