Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 49

Страница: 49 / 90

System

expansions

Fujitsu Technology Solutions

Replacing rear panel

►

Open the casing (see "Opening the casing").

►

Remove the cross-piece (see "Removing the cross-piece").

►

If necessary, remove the board bracket (see "Removing board bracket").

►

Disconnect the power supply connector (1) from the mainboard and the drives.

►

Tilt the power supply forward in the direction of the arrow (2) so that the lug (a) unhooks.

►

Carefully lift the power supply out of the casing in the direction of the arrow (3) and lay it next to
the device.

A = Rear panel for low-profile boards

B = Rear panel for long boards

►

Remove the four screws (1).

►

Pull the rear panel from the casing in the direction of the arrow (2).

Содержание ESPRIMO E5635



























































































Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Похожие инструкции для ESPRIMO E5635

Бренды по названию

Популярные бренды

Fujitsu ESPRIMO E5635, Руководство по эксплуатации

Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Похожие инструкции для ESPRIMO E5635

Бренды по названию

Популярные бренды