FujiFilm Frontier DE100 Скачать руководство пользователя страница 7

Страница: 7 / 188

- Frontier DE100 Operation Guide -

vii

Safety Instructions

Use only the type of the power supply indicated on the label.

Electric shock or fire could occur.

Do not use the power plug if any foreign materials such as dust are stuck to it.

Electric shock or fire could occur.

Make sure the blades of the power plug are fully inserted into the electrical outlet.

Electric shock or fire could occur.

Do not use the power cable if it is damaged.

Electric shock or fire could occur.

Contact your local dealer if the power cable is damaged.

Note the following points to avoid damaging the power cable.

• Do not modify the power cable

• Do not put heavy objects on the power cable

• Do not bend, twist, or pull

• Do not place it near heating appliances

Do not plug in or unplug the power cable with wet hands.

Electric shock could occur.

Do not perform daisy-chain wiring for the power cable.

It could overheat and cause a fire.

Take power directly from a residential electrical outlet.

Unplug the power cable periodically and clean between the blades and the base of the

blades.

If the power cable is left plugged in for an extended period of time, dust could

accumulate around the edge of the plug which could cause a short-circuit and a fire.

When unplugging the power cable from the electrical outlet, grasp the plug itself and

not the cable.

The cable could be damaged or the plug could be deformed and an electric shock or fire

could occur.

Make sure the printer is earthed to prevent accidental short circuits.

If the printer is used without being earthed, an electric shock or fire could occur.

Attach the earth wire for the power cable to one of the following points.

• The earth terminal on the electrical outlet

• Copper wire and so on that has been buried at least 65 cm underground.

• An earth terminal for which grounding has been performed

When attaching or removing the earth wire, the power plug must be removed from the

electrical outlet.

Check the earthing for the electrical outlet being used.

If you cannot perform earthing, contact your local dealer.

Do not connect the earth wire to the following points.

• Gas pipes (they could ignite and cause an explosion)

• Earth wires for telephone wires or lightning rods (this is dangerous as a lightning

strike causes a huge surge in electricity)

• Water pipes or faucets (earthing is not performed if there is any plastic piping in the

pipes)

CAUTION

For safety reasons, when the printer is not used for an extended period of time, unplug

the power cable from the electrical outlet.

Содержание Frontier DE100





























































































































































































Результаты поиска

Содержание Frontier DE100

Отзывы:

FujiFilm Frontier DE100, Руководство по эксплуатации, Страница: 7 / 188

Результаты поиска

Содержание Frontier DE100

Отзывы: