FujiFilm Frontier DE100 Скачать руководство пользователя страница 159

Страница: 159 / 188

- Frontier DE100 Operation Guide -

7-13

When an Error Occurs

TROUBLESHOOTING

7.1.3 Cannot Clear the Displayed Error

If an error is displayed that cannot be cleared, follow the steps below to restart the printer.

Check that the printer’s power light is on.

Press the Power switch to turn OFF the printer.

The printer’s power light turns off.

If the printer cannot be turned OFF, go to Step 3 in “If the error cannot be cleared” described

below.

Press the Power switch to turn ON the printer.

The power light turns on.

■ If the error cannot be cleared

If the printer cannot be turned OFF by pressing the power switch or if switching the printer OFF/

ON does not clear the error, restart this product by following the procedure below.

Check that the printer’s power light is on.

Press the Power switch to turn OFF the printer.

The printer’s power light turns off.

Disconnect the power cord from the printer and wait 10 seconds.

Connect the power cord to the printer.

Press the Power switch to turn ON the printer.

The power light turns on.

Note: If the error persists even after restarting, contact service support.

Содержание Frontier DE100





























































































































































































Результаты поиска

Содержание Frontier DE100

Отзывы:

FujiFilm Frontier DE100, Руководство по эксплуатации, Страница: 159 / 188

Результаты поиска

Содержание Frontier DE100

Отзывы: