Fuji Electric Frenic-Sce, Инструкция по эксплуатации

Страница: 37 / 78

5-1
Chapter 5 FUNCTION CODES
This chapter describes the function codes used to set FRENIC-Ace for Solar Pumping application.
5.1 Function Codes Table
The table below describes the function codes used to set up FRENIC Ace inverter for Solar Pumping application.
For other function codes not described in this manual refer to FRENIC Ace User
’s Manual. In case of using PMS
motor please refer to the FRENIC Ace User
’s Manual for the correct setting of motor parameters.
Code Keypad code Name Data setting range Factory
default
Setting
F02 F02 Operation method 0: Keypad operation (rotation direction input:
terminal block)
1: External signal (digital input)
2: Keypad operation (forward rotation)
3: Keypad operation (Reverse rotation) 2 1
F03 F03 Maximum output frequency 1 25.0 to 500.0 Hz 200V class
AJKU:60.0
400V class
ACE:50.0
JKU:60.0
App.
(Note 1)
F04 F04 Base frequency 1 25.0 to 500.0Hz 200V class
J:50.0
AUK:60.0
400V class
ACEJ:50.0
UK:60.0
App.
(Note 1)
F05 F05 Rated voltage at base frequency 1 0: AVR disable (output voltage proportional to
power voltage)
80 to 240 V: AVR operation (200V class)
160 to 500V: AVR operation (400V class) App.
(Note 1)
F06 F06 Maximum output voltage 1 80 to 240V: AVR operation ( 200V class)
160 to 500V: AVR operation ( 400V class) App.
(Note 1)
F07 F07 Acceleration time1 6.00
F08 F08 Deceleration time1 0.50
F09 F09 Torque boost 1 0.0 to 20.0% (% value against base frequency
voltage 1) (Note 7) App.
(Note 1)
F10 F10 Electronic thermal overload
protection for motor 1 (Select motor
characteristics) 1: Enable (For a general-purpose motor with self-
cooling fan)
2: Enable (For an inverter-driven motor (FV) with
separately powered cooling fan) 1 App.
(Note 1)
F11 F11 Electronic thermal overload
protection for motor 1 (Overload
detection level) 0.00 (disable), current value of 1 to 135% of
inverter rated current
(Inverter rated current dependent on F80) (Note 3) App.
(Note 1)
F12 F12 Electronic thermal overload
protection for motor 1 (Thermal time
constant) 0.5 to 75.0 min (Note 4) App.
(Note 1)
F37 F37 Load selection/
Auto torque boost/
Auto energy-saving operation 1 0: Variable torque load
1: Constant torque load
2: Auto torque boost
3: Auto energy-saving operation (variable torque
load)
4: Auto energy-saving operation (constant
torque load)
5: Auto energy-saving operation with auto torque
boost 1 App.
(Note 1)
F42 F42 Drive control selection 1 0: V/f control without slip compensation
1: Vector control without speed sensor (dynamic
torque vector)
2: V/f control with slip compensation
3: V/f control with speed sensor
4: V/f control with speed sensor and auto torque
boost
6: Vector control for induction motor with speed
sensor
15: Vector control for synchronous motor without
speed sensor nor pole position sensor 0 (Note 5)
200V class
J:200
AK:220
U:230
400V class
EJ:400
A:415
CK:380
U:460
0.00 to 6000 s 6.00 or
20.0