Frigidaire FLCE7522AW Скачать руководство пользователя

Страница: 10 / 54

PRE-INSTALLATION REQUIREMENTS

Electrical requirements for

laundry center with electric dryer

CIRCUIT - Individual 30 amp. branch

circuit fused with 30 amp. time delay

fuses or circuit breakers.
POWER SUPPLY - 3-wire or 4-wire, 240 volt,

single phase, 60 Hz, Alternating Current.

The dryer MUST employ a 3-conductor

power supply cord NEMA 10-30 type

SRDT rated at 240 volt AC minimum,

30 amp, with 3 open end spade lug

connectors with upturned ends or closed

loop connectors and marked for use

with clothes dryers. For 3-wire cord

connection instructions see ELECTRICAL

CONNECTIONS FOR A 3-WIRE SYSTEM.

3-Wire power supply cord kit

(not supplied)

3-wire receptacle

(NEMA type 10-

30R)

IMPORTANT

This laundry center is internally

grounded to neutral unless it was

manufactured for sale in Canada.
Only a 4-conductor cord shall be used

when the appliance is installed in a

location where grounding through

the neutral conductor is prohibited.

Grounding through the neutral link is

prohibited for: (1) new branch circuit

installations, (2) mobile homes, (3)

recreational vehicles, and (4) areas

where local codes DO NOT permit

grounding through the neutral.

Grounding type wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

WARNING

Improper grounding of the laundry

center may cause serious injury or

death. Check with a licensed electrician

if you are in doubt as to whether the

appliance is properly grounded.

OUTLET RECEPTACLE - NEMA 10-30R or

NEMA 14-30R receptacle to be located so

the power supply cord is accessible when

the dryer is in the installed position.
GROUNDING CONNECTION - See

“Grounding requirements” in Electrical

Installation section.

The dryer MUST employ a 4-conductor

power supply cord NEMA 14-30 type SRDT

or DRT (as required) rated at 240 volt

AC minimum, 30 amp, with 4 open end

spade lug connectors with upturned ends

or closed loop connectors and marked for

use with clothes dryers. For 4-wire cord

connection instructions see ELECTRICAL

CONNECTIONS FOR A 4-WIRE SYSTEM.

4-Wire power supply cord kit

(not supplied)

4-wire receptacle

(NEMA type 14-

30R)

Electrical system

requirements



NOTE

Because of potentially inconsistent

voltage capabilities, the use of this dryer

with power created by gas powered

generators, solar powered generators,

wind powered generators or any other

generator other than the local utility

company is not recommended.



NOTE

Laundry centers manufactured for sale

in Canada have factory-installed, 4-wire

power supply cord (NEMA 14-30).

Содержание FLCE7522AW























































Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды

Frigidaire FLCE7522AW, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды