Frigidaire FLCE7522AW Скачать руководство пользователя

Страница: 13 / 54

Max. Number of 90°

turns

MAXIMUM LENGTH

of 4” (102 mm) Rigid Metal Duct

STANDARD VENT MODELS

VENT HOOD TYPE

4” (10.2 cm) louvered 2.5” (6.35 cm)

56 ft. (17 m)

42 ft. (13 m)

48 ft. (14.5 m)

34 ft. (10.5 m)

40 ft. (12 m)

26 ft. (8 m)

32 ft. (9.5 m)

18 ft. (5.5 m)

The dryer must be connected to an

exhaust outdoors.

Prior to installing your

new dryer,

inspect the outdoor exhaust

opening and remove any accumulation of

lint around the outdoor exhaust opening

and in the surrounding area.

WARNING

FIRE HAZARD

A clothes dryer must be exhausted

outdoors. DO NOT exhaust dryer into

a chimney, a wall, a ceiling, an attic, a

crawl space or any concealed space of

a building. A clothes dryer produces

combustible lint. If the dryer is not

exhausted outdoors, some fine lint will

be expelled into the laundry area. An

accumulation of lint in any area of the

home can create a health and fire hazard.

WARNING

FIRE HAZARD

• DO NOT allow combustible materials

(for example: clothing, draperies/

curtains, paper) to come in contact

with exhaust system. The dryer MUST

NOT be exhausted into a chimney,

a wall, a ceiling, or any concealed

space of a building which can

accumulate lint, resulting in a fire

hazard.

• DO NOT screen the exhaust ends of

the vent system, or use any screws,

rivets or other fasteners that extend

into the duct to assemble the exhaust

system.

No screen, grate, or guard

of any mesh

size is allowed to cover

the exhaust opening.

Lint can become caught

in the screen, grate,

guard, or on the screws or

rivets, clogging the duct work

and creating a fire hazard as well

as increasing drying times

. Use an

approved vent hood to terminate

the duct outdoors, and seal all

joints with metal foil tape. All male

duct pipe fittings MUST be installed

downstream with the flow of air.

WARNING

FIRE HAZARD

Never exceed more than 3 – 90 elbows

(Standard Vent) and 4 -90 elbows

(Long Vent Models Only) in the exhaust

duct system. Exceeding the length of

duct pipe or number of elbows allowed

in the “MAXIMUM LENGTH” charts can

cause an accumulation of lint in the

exhaust system. Plugging the system

could create a fire hazard, as well as

increase drying times.

WARNING

FIRE HAZARD

To prevent the Risk of Fire, use only

the recommended exhaust duct length

chart provided by the manufacturer

for your specific model. Use Long

Vent duct lengths ONLY on laundry

center models identified as LONG

VENT. Standard Vent models are NOT

designed to operate using Long Vent

exhaust duct lengths.

WARNING

FIRE HAZARD

Failure to follow safety warnings

exactly could result in serious injury,

death, or property damage. DO NOT

install a booster fan in the exhaust

duct. Install ALL clothes dryers in

accordance with the installation

instructions in this manual.

PRE-INSTALLATION REQUIREMENTS

Содержание FLCE7522AW























































Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды

Frigidaire FLCE7522AW, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды