Frigidaire FLCE7522AW Скачать руководство пользователя

Страница: 11 / 54

PRE-INSTALLATION REQUIREMENTS

Gas supply requirements

Electrical requirements for

laundry center with gas dryer

CIRCUIT - Individual, properly polarized

and grounded 15 amp. branch circuit

fused with 15 amp. time delay fuse or

circuit breaker.
POWER SUPPLY - 2-wire, with ground,

120 volt, single phase, 60 Hz, Alternating

Current.
POWER SUPPLY CORD - The dryer is

equipped with a 120 volt 3-wire power

cord.
GROUNDING CONNECTION - See

“Grounding requirements” in Electrical

Installation section.

1. Installation MUST conform with local

codes, or in the absence of local

codes, with the National Fuel Gas

Code, ANSI Z223.1 (latest edition).

2. The gas supply line should be 1/2

inch (1.27 cm) pipe.

3. If codes allow, flexible metal tubing

may be used to connect your dryer

to the gas supply line. The tubing

MUST be constructed of stainless

steel or plastic-coated brass.

4. The gas supply line MUST have an

individual shutoff valve installed in

accordance with the B149.1, Natural

Gas and Propane Installation Code.

5. A 1/8 inch (0.32 cm) N.P.T. plugged

tapping, accessible for test gauge

connection, MUST be installed

immediately upstream of the gas

supply connection to the dryer.

6. The dryer MUST be disconnected

from the gas supply piping system

during any pressure testing of the gas

supply piping system at test pressures

in excess of 1/2 psig (3.45 kPa).

7. The dryer MUST be isolated from

the gas supply piping system

during any pressure testing of the

gas supply piping system at test

pressures equal to or less than 1/2

psig (3.45 kPa).

8. Connections for the gas supply

must comply with the Standard for

Connectors for Gas Appliances,

ANSI Z21.24 - CSA 6.10.

WARNING

EXPLOSION HAZARD

Uncoated copper tubing will corrode

when subjected to natural gas, causing

gas leaks. Use ONLY black iron,

stainless steel, or plastic-coated brass

piping for gas supply.

WARNING

Improper grounding of the laundry

center may cause serious injury or

death. Check with a licensed electrician

if you are in doubt as to whether the

appliance is properly grounded.

Grounding type wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

Water supply requirements

Hot and cold water faucets MUST be

installed within 42 inches (107 cm) of your

washer’s water inlet. The faucets MUST

be 3/4 inch (1.9 cm) with threading for

laundry hose connection. Water pressure

MUST be between 10 psi (0.69 bars) and

120 psi (8.27 bars). Pressure difference

between hot and cold cannot be more

than 10 psi. Your water department can

advise you of your water pressure.



NOTE

Washers connected to water supplies

with lower inlet pressure will experience

longer filling times and may not

complete cycles as quickly.

Содержание FLCE7522AW























































Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды

Frigidaire FLCE7522AW, Инструкция по использованию и уходу

Результаты поиска

Содержание FLCE7522AW

Отзывы:

Похожие инструкции для FLCE7522AW

Бренды по названию

Популярные бренды