background image

46

TROUBLESHOOTING 

Common washing inquiries (continued)

PROBLEM

POSSIBLE 

CAUSES

SOLUTIONS

PREVENTIVE  

MEASURES

Pilling
(Fibers ball 

up and cling 

to fabric)

• Pilling is normal 

with synthetic 

and permanent 

press fabrics due 

to abrasion from  

normal wear.

• Use a lint brush or 

shaver to remove pills.

• Use fabric softener  

in washer to lubricate  

fibers. 

• When ironing, use 

spray starch or fabric 

finish on collars and 

cuffs.

• Turn items inside out  

to reduce abrasion.

Residue or 

powder on 

dark items;
Stiff, harsh 

fabrics

• Undissolved  

detergent.

• Some granular  

detergents can 

combine with 

hard water 

minerals to form 

a residue.

• Overloading the 

washer.

• Rewash load.

• Increase water 

temperature using 

hottest water safe 

for fabric.

• DO NOT overload  

washer.

• Use liquid detergent 

or use non 

precipitating water 

conditioner with 

powder detergent.

Unexpected 

washing 

results of 

large items

• Poor movement 

of large items 

during wash 

action.

• Large items 

loaded 

incorrectly in a 

flat fashion.

• Rearrange load and  

rewash.

• Add items one at a 

time, each tightly 

bunched into its 

own ball, to allow 

beneficial item 

interaction.

• Avoid loading items in 

a flat, laid-out fashion.

Wrinkling

• Overloading the 

washer.

• Incorrect wash  

cycle for wash 

load.

• Reduce load size.

• Rinse in cold water with  

liquid fabric softener 

using the casual or 

delicate cycle.

• DO NOT overload  

washer.

• Remove items from 

washer as soon as  

cycle is completed.

• Use liquid fabric 

softener.

Yellow 

buildup of 

body soil on 

synthetic 

fabrics

• Agitation time  

too short.

• Water 

temperature too 

low.

• Not enough  

detergent.

• Soak in detergent 

booster or product 

containing enzymes.

• Wash in hottest water  

safe for fabric using  

casual cycle.

• Increase detergent.

• Add bleach safe for 

fabric or treat with color 

remover.

• Select correct wash  

cycle.

• Use correct amount  

of detergent.

• Wash synthetics  

frequently using hot  

or warm water.

Yellow or 

brown rust 

stains

• Iron or 

manganese in 

water supply, 

water pipes, or 

water heater.

• To restore discolored 

load of whites, use rust 

remover safe for fabric.

• DO NOT use chlorine 

bleach to remove rust 

stains. It may intensify  

discoloration.

• Use non precipitating 

water softener.

• Before washing, run 

hot water for a few 

minutes to clear lines.

• Drain water heater  

occasionally.

• For an ongoing 

problem, install iron 

filter in your water 

supply system.

Содержание FLCE7522AW























































Отзывы: